如果是自动清洗的打胶机，操作相当简单。只需按操作面板上的清洗按钮，机器就会自动完成清洗。那么如果机器没有自动清洗功能，该如何清洗呢?济南双组份打胶机厂家给您建议。

If it is an automatic cleaning glue applicator, the operation is quite simple. Just press the cleaning button on the operation panel, and the machine will automatically complete cleaning. How to clean the machine if it does not have automatic cleaning function? Jinan two-component sealant manufacturer gives you suggestions.

先来，看看胶水的性质。如果胶水是单液，在室温下不易凝固，那么下次使用的胶水在每一点或产品填充后都是一样的，就不能考虑清洗问题了。如为厌氧胶、快干胶、401502胶或硅胶胶等常温下会快速凝固的胶，应清洗干净。清洗时，先将未使用的胶水沥干，再将天南水、工业酒精等有机溶剂放入机器内。然后把这些有机溶剂压在一起，用气枪把它们吹开。

First, look at the properties of glue. If the glue is a single liquid, which is not easy to solidify at room temperature, the glue used next time will be the same at every point or after the product is filled, so the cleaning problem cannot be considered. If it is anaerobic glue, quick drying glue, 401502 glue or silica gel glue that will rapidly solidify at room temperature, it should be cleaned. When cleaning, drain the unused glue, and then put organic solvents such as Tiannan water and industrial alcohol into the machine. Then press these organic solvents together and blow them away with an air gun.

对于这种机器，清洗是非常必要的。否则胶水在胶阀或料筒内固化会很麻烦，有些配件可能需要更换。所以每次用的时候，一定要记得清洗!双组份打胶机的a、B胶的混合部分在出胶口只有混合管，所以清洗部分只有混合管，其他部分不需要清洗;

For this kind of machine, cleaning is very necessary. Otherwise, it will be troublesome for the glue to solidify in the glue valve or cylinder, and some accessories may need to be replaced. So every time you use it, remember to clean it! The mixing part of glue a and glue B of the two-component sealant beater only has a mixing pipe at the glue outlet, so the cleaning part only has a mixing pipe, and other parts do not need to be cleaned;

如果是双组份打胶机，清洗比较简单。工作完成后，将打胶机前的白色搅拌管拆下，浸泡在有机溶剂中，或更换搅拌管。

If it is a two-component sealant dispenser, cleaning is relatively simple. After the work is completed, remove the white mixing pipe in front of the glue applicator, soak it in organic solvent, or replace the mixing pipe.

总之如果打胶机没有一键清洗功能，清洗时先将未使用完的胶水排干，然后将有机溶剂，如天那水、工业酒精等放入机器内；然后将这些有机溶剂和胶水一起压出来，再用气枪吹开即可。用此类型的机器，清洗是十分必要的，否则的话，长时间不用，胶水固化在胶阀中，或者是料桶中就很麻烦，可能有些配件就要更换了。

In a word, if the glue dispenser does not have one key cleaning function, drain the unused glue before cleaning, and then put organic solvents, such as Tianna water and industrial alcohol, into the machine; Then press these organic solvents and glue together, and blow them with an air gun. With this type of machine, cleaning is very necessary. Otherwise, if it is not used for a long time, it will be troublesome if the glue is solidified in the glue valve or in the bucket. Some parts may need to be replaced.

所以每次用完后，一定要记得清洗。更多相关打胶机的事项了解就来我们网站http://www.jntiannuo.com进行咨询了解吧！

So every time you use it, you must remember to clean it. For more information about the glue dispenser, please come to our website http://www.jntiannuo.com Consult and understand!