双组份打胶机选用PLC控制，并选用多泵运动供胶，在运行全过程中不容易造成死点，混料均匀打胶平稳，并制定供胶桶出胶口在正下方，胶不容易造成残留浪费问题，对胶的流淌性规定不高（流淌性好点的胶），如果胶太稠出胶不顺畅，该机的出胶压力可及时调节，运动频率低磨损少。为此小编对双组份打胶机出现断胶的解决方法如下：

The two-component glue dispenser is controlled by PLC, and the multi pump movement is used for glue supply. It is not easy to cause dead spots during the whole operation process. The mixing is even and stable. The glue outlet of the glue supply bucket is directly below, so the glue is not easy to cause residual waste. The regulations on the fluidity of the glue are not high (glue with better fluidity). If the glue is too thick and the glue is not smooth, the glue outlet pressure of the machine can be adjusted in time, and the movement frequency is low and the wear is less. For this reason, the solution to break the two-component glue dispenser of the small knitting machine is as follows:

一、双组份打胶机是为了增加制作效率调节是输送带的速度迅速，出胶量无法调节，造成时断时续的根本原因之一。

1、 The two-component rubber beater is designed to increase the production efficiency. The adjustment is one of the fundamental reasons for the rapid speed of the conveyor belt and the inability to adjust the rubber output, causing intermittent.

二、针对胶缸和胶头的温度没设置好，到时有的胶没达到应有的温度，造成出现锯齿状类的状态。

2、 The temperature of the rubber cylinder and the rubber head is not set properly, and some rubber does not reach the proper temperature, resulting in a serrated state.

三、双组份打胶机建议把温度调节到合适的温度，使丁基胶化掉，如此几乎不容易出现以上难题。

3、 It is recommended to adjust the temperature of two-component rubber beater to a proper temperature to melt the butyl rubber, so that the above problems are hardly likely to occur.

四、如果是从双组份打胶机一开始用到到现在一直是这种状态胶头出胶口有毛刺胶头一般有二种胶口处有槽和无槽二种。

4、 If the two-component sealant dispenser has been in this state since it was first used, there are generally two types of rubber head with burr at the rubber outlet: the rubber head with groove and the rubber head without groove.

五、换胶后出现这种状态温度到达上限后出胶异常胶口处胶没完全融化手动排出来一小部分胶也就是打几个框子将压力调大多打几个框子将胶缸内的胶挤实。

5、 After changing the rubber, this state occurs. After the temperature reaches the upper limit, the glue at the abnormal glue outlet is not completely melted. A small amount of glue is discharged manually, that is, several frames are set to adjust the pressure, and several frames are set to squeeze the glue in the glue tank.

六、双组份打胶机采购的丁基胶质量差，硬件配置低成本，杂质阻塞造成的。

6、 The butyl rubber purchased by two-component rubber beater is of poor quality, low hardware configuration cost, and caused by impurities blocking.

七、放胶后没进行放气。

7、 No air bleeding was carried out after putting glue.

双组份打胶机出现断胶的解决方法就从七个方面来讲解了问题，当然您在使用打胶机前后要注意它的检查与维护，才能大限度的避免问题的产生。更多相关实现就来我们网站http://www.jntiannuo.com咨询了解吧！

The solution to break of two-component sealant dispenser is explained from seven aspects. Of course, you should pay attention to its inspection and maintenance before and after using the sealant dispenser to avoid problems to a large extent. More related implementations come to our website http://www.jntiannuo.com Ask and understand!