打胶机的液压缸工作不正常原因及维护
双组份打胶机试用期间会有问题出现，这并不少见，那么你知道打胶机的液压缸工作不正常原因及维护是怎样的吗？下面
济南双组份打胶机厂家为您讲解。
It is not uncommon for the two-component sealant dispenser to have problems during the trial period. Do you know the cause of abnormal operation of the hydraulic cylinder of the sealant dispenser and how it is maintained? Next, Jinan two-component sealant manufacturer will explain to you.
打胶机的液压缸工作不正常原因
Reasons for abnormal operation of hydraulic cylinder of glue applicator
A、液压站工作压力不正常，检查比例溢流阀，进行清洗；电机工作是否正常；油泵工作是否正常
A. If the working pressure of the hydraulic station is abnormal, check and clean the proportional overflow valve; Whether the motor works normally; Whether the oil pump works normally
B、电磁换向阀工作是否正常，检查线圈和阀体
B. Check whether the solenoid directional valve works normally. Check the coil and valve body
C、检查油管是否有漏油现象
C. Check the oil pipe for oil leakage
D、检查油缸是否有泄漏现象
D. Check the oil cylinder for leakage
维护与保养：
Maintenance:
A、新机器经过一段时间的运转之后，应打开护板，检查各紧固件是否有松动现象，并重新紧固。
A. After a period of operation of the new machine, open the guard board, check whether the fasteners are loose, and retighten them.
B、每次使用完毕，要将机器上的残胶及灰尘干净，使传送带及机器外表保持清洁。
B. After each use, remove the residual glue and dust on the machine to keep the conveyor belt and machine surface clean.
C、输送装置两侧主动轮和从动轮轴承每隔3个月应加注一次润滑油脂。
C. The driving wheel and driven wheel bearings on both sides of the conveyor shall be filled with lubricating grease every 3 months.
D、液压系统使用抗磨液压油应半年更换一次，并定期检查系统是否有漏油现象。
D. The anti-wear hydraulic oil used in the hydraulic system shall be replaced every six months, and the system shall be checked regularly for oil leakage.
E、环境温度在5℃以上时，使用46号抗磨液压油；不高于5℃时，使用32号抗磨液压油。
E. When the ambient temperature is above 5 ℃, 46 # anti-wear hydraulic oil shall be used; When the temperature is not higher than 5 ℃, use No. 32 anti-wear hydraulic oil.
F、定期检查电气接线是否有松动及接地的可靠性。
F. Regularly check whether the electrical wiring is loose and whether the grounding is reliable.
G、B泵的过滤器与过滤器每隔一个月清洗一次。
G. The filter and filter of pump B shall be cleaned every other month.
H、A与B胶的混合器每隔七天清洗一次。
H. The mixer of glue A and glue B shall be cleaned every seven days.
I、连接混合器的连接座每隔一个月清洗一次。
1. The connection seat connecting the mixer shall be cleaned every other month.
J、清洗胶轴套上残余的胶，保证胶轴套转动灵活。
J. Clean the residual rubber on the rubber shaft sleeve to ensure that the rubber shaft sleeve can rotate flexibly.
The reasons for abnormal operation of the hydraulic cylinder of the glue dispenser and the maintenance related matters are explained here. If you have any questions, please come to our website http://www.jntiannuo.com Consult!
上一篇：打胶机胶头堵住的情况进行有效处理
下一篇：建议使用双组份打胶机之前行调试
