为了让生产的效率更高，双组份打胶机在在正式投入生产之前是需要花点时间去调试的，尤其是要去设置程序，同时有很多的配件都需要调试，那么怎么调试双组份打胶机呢？

In order to make the production more efficient, it takes some time to debug the two-component sealant dispenser before it is officially put into production, especially to set up the program. At the same time, many accessories need to be debugged. How to debug the two-component sealant dispenser?

1、机台摆放位置的水平

1. The levelness of the machine table placement position

双组份打胶机的调试要保持双组份打胶机平台水平度，打好平台水平相当于调试好了一半，不然则容易出现点偏、多胶少胶、溢胶等问题。

For the commissioning of two-component sealant dispenser, the levelness of the two-component sealant dispenser platform shall be maintained. A good platform level is equivalent to half of the commissioning. Otherwise, problems such as point deviation, more glue, less glue and overflow are likely to occur.

2、选择合适的针头

2. Select the right needle

自动双组份打胶机针头内部的直径应该和胶点直径的1/2左右，可根据产品大小来选取合适的点胶针头，针头小内径为0.1毫米。

The inner diameter of the needle of the automatic two-component dispensing machine should be about 1/2 of the diameter of the glue point. The proper dispensing needle can be selected according to the size of the product. The small inner diameter of the needle is 0.1mm.

3、点胶针头与点胶位置的高度距离调节

3. Height distance adjustment between dispensing needle and dispensing position

双组份打胶机需要调试点胶高度，针尖到产品的距离过高，会出现拉胶问题；点胶高度太低又会出现针头沾胶、爬胶、胶量不均匀等问题。

The two-component glue dispenser needs to adjust the dispensing height. If the distance between the needle tip and the product is too high, the glue pulling problem will occur; If the dispensing height is too low, problems such as glue sticking on the needle, glue creeping, and uneven glue amount will occur.

4、出胶时间的调试

4. Commissioning of dispensing time

自动双组份打胶机的点胶量的设定应该为产品间距的1/2，保证有足够的点胶量粘贴组件，防止过多的胶水渗出；调试出胶时间可以控制好点胶量。

The dispensing amount of the automatic two-component sealant dispenser should be set at 1/2 of the product spacing, so as to ensure that there is enough dispensing amount to paste the components and prevent excessive glue from seeping out; Adjust the dispensing time to control the dispensing amount.

5、压力设定调试

5. Pressure setting commissioning

双组份打胶机的控制器把压力提供给胶管和针头，通过调节双组份打胶机压力大小，可以控制出胶量和点胶的速度，压力过强容易出现胶水喷出的问题，压力太弱则会出现点胶不均匀和漏点的现象。

The controller of the two-component glue dispenser supplies pressure to the rubber tube and needle. By adjusting the pressure of the two-component glue dispenser, the amount of glue and the speed of dispensing can be controlled. If the pressure is too strong, the problem of glue spraying is likely to occur. If the pressure is too weak, the phenomenon of uneven dispensing and leakage will occur.

6、胶水温度控制

6. Glue temperature control

一般环氧树脂胶水应保存在0～5℃的冰箱中，使用时提前半小时拿出，使胶水温度与工作环境一致，胶水的使用温度应为23℃～25℃，注意对环境温度进行控制。

Generally, the epoxy resin glue should be stored in a refrigerator with a temperature of 0~5 ℃. Take it out half an hour in advance to make the glue temperature consistent with the working environment. The glue should be used at a temperature of 23 ℃~25 ℃. Pay attention to the control of the ambient temperature.

经过这些步骤的调试后，双组份打胶机就可以自动投入工作了。调试是为了提高生产效率，防止工作过程中出现故障影响生产，因此，操作都需要学会调试双组份打胶机。更多相关内容就来我们网站http://www.jntiannuo.com咨询吧！

After the debugging of these steps, the two-component sealant machine can be put into operation automatically. Debugging is to improve the production efficiency and prevent the production from being affected by faults in the working process. Therefore, operators need to learn how to debug the two-component sealant dispenser. More relevant content will come to our website http://www.jntiannuo.com Consult!