随着社会的发展,我们进入了自动化时代,由于自动化机器给人们带来了较大地方便，双组份打胶机就是专门对流体进行控制,并将流体点滴、涂覆于产品表面或产品内部的自动化机器，下面小编为大家介绍济南双组份打胶机组成部分是怎样保养的吧，

With the development of society, we have entered the era of automation. Because automation machines have brought great convenience to people, two-component glue dispenser is an automatic machine that controls the fluid and drips and coats the fluid on the surface or inside of the product. The following sections will introduce how to maintain the components of Jinan two-component glue dispenser,

1，两个马达的加油，主马达与辅料马达进气口均安装有油雾器,当其中的油低于低端刻线时应拆下油杯加注10号机油，如果油雾器不滴油或者马达严重缺油时可将主马达进气管与马达连接处的活接拆掉,用油枪想里面加油,辅料马达可将其端盖螺母拧开加油，

1. For oil filling of the two motors, the air inlets of the main motor and auxiliary motor are equipped with oil foggers. When the oil in the oil foggers is lower than the low end reticle, the oil cup should be removed and 10 # engine oil should be added. If the oil foggers do not drip oil or the motor is seriously short of oil, the union joint at the connection between the main motor air inlet pipe and the motor can be removed, and the oil gun can be used to fill the inside. The auxiliary motor can unscrew its end cap nut for oil filling,

2，主泵,辅料泵,配比泵经过一段时间的使用后会有胶从里面渗漏出,流到油碗里，可以把胶清理掉,加注机油，用十字螺丝刀类顶住主,辅两泵油碗下端的圆孔处按顺时针方向紧固油碗;配比泵油碗用扳手拧紧即可，

2. After using the main pump, auxiliary material pump and proportioning pump for a period of time, glue will leak out from the inside and flow into the oil bowl. You can clean the glue, add oil, and use a cross screwdriver to counter the main pump and the auxiliary pump. Tighten the oil bowl clockwise at the round hole at the lower end of the oil bowl; Tighten the matching pump oil bowl with a wrench,

3，阀的注油用油枪向阀的小孔注油,可以防止生锈，

3. The oil gun is used to inject oil into the small hole of the safety valve to prevent rust,

4，Y型过滤器其位置在辅料泵出口处,清洗时将端盖拧下,用煤油浸泡,用牙刷类刷子刷干净，安装时将网放在端盖里用手拧到底,再用扳手拧紧，用一组胶洗一次,如无杂质两组胶洗一次,灵活掌握，

4. The Y-type filter is located at the outlet of the auxiliary material pump. When cleaning, unscrew the end cover, soak it in kerosene, and brush it clean with a toothbrush. During installation, put the net in the end cover and screw it to the end by hand, then tighten it with a wrench, and wash it once with one set of glue. If there is no impurity, wash it once with two sets of glue, and you will be flexible,

5，大过滤器其位置在高压表B表右下,拧下回流阀下方胶管,拧下过滤器,将网及网芯取出,弹簧、取出,刷干净,将弹簧小孔套在网芯的凸点上，倒着装入器体后转过来拧在胶机上，用3-5组洗一次,如无杂质,灵活掌握。

5. The large filter is located at the bottom right of the high pressure gauge B. Unscrew the rubber hose under the return valve, unscrew the filter, take out the screen and the screen core, take out the spring, brush it clean, cover the small spring hole on the convex point of the screen core, install it upside down into the device body, turn it around and screw it on the glue machine, and wash it once with 3-5 groups. If there is no impurity, master it flexibly.

以上就是有关于打胶机组成部分的五点保养事项的相关内容了，您对此有什么不理解的地方或者有什么相关需求，都能随时来我们网站http://www.jntiannuo.com留言咨询！

These are the five points about the maintenance of the glue dispenser components. If you have any questions or needs, you can come to our website at any time http://www.jntiannuo.com Message consultation!