双组份打胶机在咱们平常的运用过程中有许多需求留意的事项，假如咱们平常不留心留意这些当地很可能会形成咱们的双组份打胶机出现各种各样的故障，这样不光影响你的生产功率下降你的收益还会大幅度的下降设备的寿数。总之打胶机设备平常使用中要进行定期检查，下面小编为您讲解。

There are many things we need to pay attention to when using two-component glue dispensers. If we don't pay attention to these places, it is likely that our two-component glue dispensers will have various failures, which will not only affect your production power, but also greatly reduce your income and the life of the equipment. In a word, the glue dispenser equipment should be inspected regularly during normal use. The following sections will explain to you.

●清洁喷枪表面、清理喷嘴，确保喷嘴的畅通;

● Clean the surface of the spray gun and the nozzle to ensure that the nozzle is unblocked;

●清洁或替换双组份打胶机和喷枪的过滤网;

● Clean or replace the filter screen of two-component sealant dispenser and spray gun;

●查看喷枪是否有漏胶现象，如有漏胶现象请调理，维修、替换喷枪、喷头、喷嘴等需求替换的部件。

● Check whether the spray gun has glue leakage. If there is glue leakage, please adjust, repair and replace the spray gun, nozzle, nozzle and other parts that need to be replaced.

●查看胶缸内壁是否有炭化层，如有炭化层请运用诺信专用清洗液R溶剂清洗胶缸。

● Check whether there is a carbonized layer on the inner wall of the rubber cylinder. If there is a carbonized layer, please use the special cleaning solution R solvent of Nuoxin to clean the rubber cylinder.

●将双组份打胶机加热操作温度，排空胶箱内的热溶胶。查看胶缸内是否有杂质，如有杂质用干净的抹布清洁胶缸。

● Heat the two-component sealant beater to the operating temperature, and drain the hot glue in the glue box. Check whether there are impurities in the rubber cylinder. If there are impurities, clean the rubber cylinder with a clean rag.

●查看一切接线盒和接线柱是否结实;

● Check whether all junction boxes and terminals are solid;

●查看一切电源衔接线是否有破损现象，其他绝缘件是否牢靠;

● Check whether all power cord connections are damaged and whether other insulating parts are secure;

●清洁及查看双组份打胶机电器箱内部;

● Clean and check the interior of the electrical box of the two-component sealant dispenser;

●查看一切电源衔接线衔接是否牢靠。

● Check whether all power supply cables are connected securely.

此外由于双组份打胶机每次冲刷混合器不会很干净，每次都有少量的混合胶堆积，越来越多，致使堵塞混合器通道，用一段时间后，影响出胶量和混合作用，因而要定时(聚硫胶五天，硅酮胶两天)清洗混合器。把混合器内的混胶棒拆出，如有损坏替换新的混胶棒。若混胶棒拆不出来，可用火烧掉，留意不能损害零件螺纹。

In addition, since the two-component rubber beater is not very clean each time it washes out the mixer, a small amount of mixed glue accumulates each time, which leads to blockage of the mixer channel. After a period of time, the glue output and mixing effect will be affected, so the mixer should be cleaned regularly (five days for polysulfide glue and two days for silicone glue). Remove the glue mixing rod in the mixer and replace it with a new one if it is damaged. If the rubber mixing rod cannot be removed, it can be burned off. Be careful not to damage the thread of the part.

以上就是小编为您讲解的关于打胶机的事项，您对此有什么需求可以随时来我们网站http://www.jntiannuo.com进行咨询，有关人员为您竭诚服务！

The above is what Xiaobian explained to you about the glue dispenser. You can come to our website at any time if you have any needs http://www.jntiannuo.com For consultation, relevant personnel will serve you wholeheartedly!