一般情况下，打胶机是中空玻璃自动生产线上的后一个环节。一般在压合段的后面，它是对已经组装和压合好的中空玻璃进行打胶。济南双组份打胶机厂家为解说基本次序，如下：

Generally, the glue applicator is the last link in the automatic production line of insulating glass. Generally, it is behind the pressing section, which is used to glue the assembled and pressed insulating glass. Jinan two-component sealant manufacturer explains the basic sequence as follows:

（1）未打胶的玻璃由前面连接的单元送入，当玻璃到达测量装置时停止输送。

(1) The unglued glass is fed into the front connected unit, and the glass is stopped when it reaches the measuring device.

（2）测量总宽度W，并根据手工输入的g1和g2值计算出打胶宽度。W-g1-g2=b

(2) Measure the total width W, and calculate the gluing width according to the manually entered g1 and g2 values. W-g1-g2=b

(3)测量完毕后，玻璃进入吸盘吸附区停止吸盘伸出完全吸附后吸盘与输送带同步向打胶区输送。

(3) After the measurement is completed, the glass enters the suction cup adsorption area and stops the suction cup stretching out for complete adsorption. After that, the suction cup and the conveyor belt are transported to the glue area synchronously.

(4)当玻璃尾边到达枪头时，停止传送，进行定位后，升降机构上升开始进行一边打胶。

(4) When the tail edge of the glass reaches the gun head, stop the transmission. After positioning, the lifting mechanism rises and starts to apply glue at the same time.

(5)当上升到玻璃上边缘时，由测量机构测量玻璃的高度H值，枪头翻转90度、下支撑就翻上、枪头位、角注胶后，玻璃开始反向输送，对上边（二边）进行打胶。

(5) When it rises to the upper edge of the glass, the measuring mechanism measures the height H value of the glass. After the gun head is turned 90 degrees, the lower support is turned up, and the gun head is positioned and the corner is filled with glue, the glass starts to be transported in reverse, and the upper (two sides) are filled with glue.

(6)当按测量好的长度输送完毕，打完上边后，枪头翻转90度、就位、角注胶后。枪头向下运动，对第三边进行打胶。

(6) When the conveying is completed according to the measured length, and the upper edge is drilled, the gun head is turned 90 degrees, in place, and the corner is filled with glue. The gun head moves downward to apply glue to the third side.

(7)枪头到达底边后翻转90度、就位、角注胶。玻璃向前输送，对底边（第四边）进行打胶，并按测量好的长度值运动。进行第四角注胶。完成打胶。

(7) Turn the gun head 90 degrees after reaching the bottom edge, put it in place, and inject glue into the corner. The glass is transported forward, the bottom (fourth side) is glued and moved according to the measured length value. Carry out glue injection for the fourth corner. Complete glue application.

(8)打胶完毕后，吸盘脱离并返回原来区域，玻璃继续向前移动。到达输送段后延时停止。由人工取下打好胶的玻璃。下一片玻璃进入打胶区，开始下一个循环。

(8) After the glue is applied, the suction cup will disengage and return to the original area, and the glass will continue to move forward. It stops after reaching the conveying section. Remove the glued glass manually. The next piece of glass enters the glue area and starts the next cycle.

所有的控制操作由放置在机器正前面的控制电脑来完成，其界面应完成所有操作并进行参数设置和数据调整，并有自动故障诊断功能，适时显示状态和有关数据。更多相关内容您可以来我们这里http://www.jntiannuo.com咨询了解！

All control operations shall be completed by the control computer placed in the front of the machine. Its interface shall complete all operations and carry out parameter setting and data adjustment. It shall also have the automatic fault diagnosis function to display the status and relevant data timely. You can come to us for more information http://www.jntiannuo.com Ask about it!