There are different types of glue machines that often use glue, which can be said to be more than the same products. Each model has different performance. The glue commonly used for glue coating can be used at the end of the channel. Only some common glue can be commented on to meet the use methods of some basic coating industries and pressure buckets.

　　一、普通胶水型

　　I. ordinary glue type

　　胶机常用的涂层胶分别用银胶、红胶、热熔胶、硅胶、AB胶、快干胶、焊锡膏、环氧天然橡胶、填充底部的橡胶、乙烯基、厌氧胶、耐高温胶、白胶等等,这些都是常用的涂层胶,胶与通道胶机可以使用,但需要更换一些配件,可以满足生产的需要,上胶阀对上胶有少量的要求较高，类似于硅胶、热熔胶、红胶、厌氧胶等需要特殊上胶阀设备才能真正上胶的末端要求。

　　The coating glue commonly used in glue machine is silver glue, red glue, hot melt glue, silica gel, AB glue, quick drying glue, solder paste, epoxy natural rubber, rubber filled with bottom, vinyl, anaerobic glue, high temperature resistant glue, white glue, etc. These are commonly used coating glue. Glue and channel glue machine can be used, but some accessories need to be replaced to meet the production needs. There is a small amount of glue on glue valve High requirements, similar to silica gel, hot-melt glue, red glue, anaerobic glue, etc. need special glue valve equipment to really glue the end requirements.

　　二、使用压力斗要注意问题

　　II. Precautions in using pressure bucket

　　这些类型的胶水要求适用于灌装压力桶吗?对特定的需求,自动化生产是不需要通过更换可能每次胶,使用气动式压力桶来满足通道胶机连续胶的要求,只有压力桶必须注意使用方法,或特别容易出现胶水供应不足,导致没有胶水,胶水使用胶水每个日出生产是非常大的。

　　Are these types of glue requirements applicable to filling pressure barrels? For specific needs, automatic production does not need to replace every glue. Pneumatic pressure barrels are used to meet the continuous glue requirements of the channel glue machine. Only the pressure barrels must pay attention to the use method, or they are particularly prone to insufficient glue supply, resulting in no glue. Every sunrise production with glue is very large.

　　三、使用灌桶

　　III. use of buckets

　　如何使用气动压力鼓的通道填料使用?相对短暂,要了解胶水的性质,然后观察浓度条件下,特别容易冷凝式连续混合,避免冷凝,更高水平的胶是一样的,有一个低降水的胶水,胶水浓度还需要添加混合,然后加入胶桶式气压,气压管、压力释放阀、防爆阀、等,密封,以避免泄漏,然后接软管胶机、这样的基本是连通的。先在压力桶中充分充气后，再用槽胶机将胶水泵出，以免造成胶水间歇时产生问题。

　　How to use the channel packing of the pneumatic pressure drum? It is relatively short. First, understand the nature of the glue, and then observe the condition of concentration. It is very easy to mix continuously with condensation to avoid condensation. The higher level glue is the same. There is a glue with low precipitation. The glue concentration also needs to be mixed, and then add the rubber barrel type air pressure, air pressure pipe, pressure relief valve, explosion-proof valve, etc. to seal to avoid condensation No leakage, then connect the hose rubber machine, which is basically connected. First, fully inflate the pressure barrel, and then pump out the glue with the slot glue machine, so as not to cause problems when the glue is intermittently.