双组份打胶机具有操作准确、效率快、品质好等优势，对于实现企业大批量生产有着关键性作用。而双组份打胶机作为自动化机械设备，在操作方面有着严格的要求。下面小编为您讲讲双组份打胶机的一些操作规程事项。

The two-component sealant dispenser has the advantages of accurate operation, fast efficiency and good quality, which plays a key role in realizing mass production of enterprises. As an automatic mechanical equipment, the two-component rubber beater has strict requirements in operation. The following section will tell you about some operating procedures of two-component sealant dispenser.

双组份打胶机操作规程：

Operating procedures of two-component sealant dispenser:

1、在安装双组份打胶机时，需要产品的固定架，打开气压、机器电源，在胶管内灌入需要使用的胶水，固定好胶管使用高度；

1. When installing the two-component sealant dispenser, you need the fixed frame of the product, turn on the air pressure and machine power, fill the required glue into the rubber tube, and fix the use height of the rubber tube;

2、编程：根据产品点胶图形，编制程序。程序编好后设置点胶速度、Z轴提高高度相对值、点胶时间参数；

2. Programming: according to the product dispensing graphics, prepare the program. After programming, set dispensing speed, relative value of Z-axis height increase and dispensing time parameters;

3、气压设定：根据胶水粘稠度设置对应使用气压；

3. Air pressure setting: set the corresponding air pressure according to the glue viscosity;

4、程序、设置完成后，按下机器上的RUN/TEACH开关，放置产品按下Start键开始点胶，每换产一只产品，都需按下Start键；

4. After the program and settings are completed, press the RUN/TEACH switch on the machine, place the product and press the Start key to start dispensing. Press the Start key every time a product is changed;

5、完成点胶工作后或中途长时间不进行点胶工作时，需及时清洗针头，以防针头堵塞。

5. After the dispensing work is completed or when the dispensing work is not carried out for a long time, the needle shall be cleaned in time to prevent the needle from blocking.

此外要知道，在使用双组份打胶机之前，在操作设备之前，厂家的操作工作人员须完全了解双组份打胶机的操作。启动机器前，检查电源和电压是否稳定。开机后，应该注意机器是否发出异常噪音。如果是，应立即关闭机器，并在检查问题后打开机器。

In addition, before using the two-component sealant dispenser and operating the equipment, the manufacturer's operating personnel must fully understand the operation of the two-component sealant dispenser. Before starting the machine, check whether the power supply and voltage are stable. After startup, pay attention to whether the machine makes abnormal noise. If so, shut down the machine immediately and turn it on after checking the problem.

以上内容就是关于双组份打胶机操作规程事项，相信大家已经有所了解。建议您在使用之前做好相关的检查事项，促进高质量的顺利使用，更多相关内容就来我们网站http://www.jntiannuo.com进行咨询了解吧！

The above contents are about the operating procedures of two-component sealant dispenser, and I believe you have already understood them. It is recommended that you do a good job of relevant inspections before use to promote the smooth use of high-quality products. More relevant content will come to our website http://www.jntiannuo.com Consult and understand!