双组份打胶机在咱们平常的运用过程中有许多需求留意的事项，假如咱们平常不留心留意这些当地很可能会形成咱们的双组份打胶机出现各种各样的故障。下面就来介绍一番吧。

There are many things we need to pay attention to when using the two-component sealant dispenser. If we do not pay attention to these places, it is likely that our two-component sealant dispenser will have various failures. Now let's introduce it.

1、双组份打胶机的压盘上的放气阀门要坚持晓畅，要定时疏通和清洗。

1. The vent valve on the pressure plate of the two-component sealant dispenser shall be unblocked and cleaned regularly.

2、正常作业时不要断气源，假如发现断气源应中止作业。

2. Do not cut off the gas source during normal operation. If the gas source is cut off, stop the operation.

3、若涂胶作业过程中中止时间超过15分钟以上时，必定要用“冲枪”。本机有报警功用，届时没有冲胶会有蜂鸣器报警。

3. If the stop time exceeds 15 minutes during the gluing operation, the "punching gun" must be used. This machine has alarm function, and there will be buzzer alarm when there is no glue preparation.

4、定时查看气源，先应确保运用经枯燥的洁净压缩空气，并定时排放分离过滤器中的积水，查看油雾器中的油是否够用。

4. Check the air source regularly. First, make sure to use the dry and clean compressed air, regularly discharge the water in the separation filter, and check whether the oil in the oil atomizer is sufficient.

5、双组份打胶机的组份遇空气会结壳，影响泵的正常作业和管路的畅通，因而，停机时B组份胶的一切通道在泄压后均应关闭，使B组份不得接触空气。

5. The components of the two-component sealant dispenser will crust when encountering air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B sealant shall be closed after pressure relief during shutdown, so that component B shall not contact the air.

6、B胶桶内假如要有空气，空气将排不出来，B泵将快速往复运动，不能向高压泵内正常供胶，影响整个体系，因而，须将空气排出来。办法是：将压盘提出从新压入并放气。

6. If there is air in the rubber barrel B, the air will not be discharged, and the pump B will move back and forth rapidly, so it cannot supply glue to the high-pressure pump normally, affecting the whole system. Therefore, the air must be discharged. The method is: lift the pressure plate and press it in again and bleed.

7、液压站体系的压力，不能调的太高，要根据室内环境温度等实际情况，调满意胶嘴正常出胶均匀打胶即可。翻开液压站时必定要翻开胶枪，否则B组份管路压力将升得很高，形成事故。

7. The pressure of the hydraulic station system should not be adjusted too high. It should be adjusted to a satisfactory level according to the actual conditions such as indoor ambient temperature. When opening the hydraulic station, the glue gun must be opened, otherwise the pressure of component B pipeline will rise very high, causing a safety accident.

8、A胶提胶泵连续作业1分钟以上没有供胶中止，阐明管路内有空气，此刻会报警，须翻开泵上管接头再翻开A胶提胶泵，直到出胶为止，中止并接好接头，胶枪会出现有空气的哔哔爆炸声，空气排净就好了。

8. The glue pump A has been operating continuously for more than 1 minute without stopping the glue supply. It indicates that there is air in the pipeline, and an alarm will be given at this moment. You must turn over the pipe connector on the pump and then turn over the glue pump A until the glue is released. Stop and connect the connector. The glue gun will have a beeping explosion sound of air, and the air will be exhausted.

9、由于双组份打胶机每次冲刷混合器不会干净，每次都有少量的混合胶堆积，越来越多，致使堵塞混合器通道，用一段时间后，影响出胶量和混合作用，因而要定时(聚硫胶五天，硅酮胶两天)清洗混合器。把混合器内的混胶棒拆出，如有损坏替换新的混胶棒。若混胶棒拆不出来，可用火烧掉，留意不能损害零件螺纹。

9. As the two-component rubber beater will not clean each time it washes the mixer, a small amount of mixed rubber will accumulate each time, which will block the mixer channel. After a period of time, the rubber output and mixing effect will be affected, so the mixer should be cleaned regularly (five days for polysulfide rubber and two days for silicone rubber). Remove the glue mixing rod in the mixer, and replace it with a new one if it is damaged. If the rubber mixing rod cannot be removed, it can be burned off. Be careful not to damage the thread of the part.

双组份打胶机在平常生产操作中的留意事项的问题在这里就讲九个要点了，当然还有很多留意事项要在使用前后多了解多注意，有问题及时解决就行。关注我们http://www.jntiannuo.com了解更多！

Here are nine key points for the precautions of two-component sealant dispenser in normal production and operation. Of course, there are many precautions that should be learned and paid more attention before and after use, and problems should be solved in time. Follow us http://www.jntiannuo.com Learn more!