打胶机呈现花胶以及打胶不丰满的原因
双组份打胶机出现的很多问题无论是进口的立式打胶机仍是卧式打胶机都会经常呈现的一种毛病，为了后面更好更顺利的进行使用，我们来讲讲打胶机呈现花胶以及打胶不丰满的原因。
There are many problems with the two-component sealant dispenser, whether it is an imported vertical sealant dispenser or a horizontal sealant dispenser. In order to use it better and more smoothly, let's talk about the reasons why the sealant dispenser presents the pattern glue and the sealant is not full.
双组份打胶机呈现花胶：
The two-component glue applicator presents the glue:
1、双组份打胶机的混胶器内胶体过多固话，阻力增大。
1. There are too many colloids in the mixer of the two-component sealant beater, and the resistance increases.
2、A或B胶胶桶内无胶，胶已用完。
2. There is no glue in A or B glue bucket, and the glue has been used up.
3、A或B胶胶桶内有空气。
3. There is air in A or B glue bucket.
4、针阀或单向阀阻塞。
4. The needle valve or check valve is blocked.
咱们仔细观察导致花胶的毛病原因会发现大多是因为设备没有定时保护清洗导致的。所以咱们一定要牢记设备一定要定时保护清洗的良好习惯。
If we carefully observe the causes of the problems of the glue, we will find that most of them are caused by the equipment not being protected and cleaned regularly. So we must remember that the equipment must be regularly cleaned to protect the good habit.
双组份打胶机产生打胶不丰满：
The two-component gluing machine produces incomplete gluing:
一种状况是因为咱们将打胶机的打胶速度设置的过快导致的。有的客户为了加速自己的生产节奏追逐生产计划，将打胶速度以为调整的过快，导致胶体还没有达到合格标准机头就已经移动到下一个位置进行打胶操作了。
One condition is that we set the dispensing speed of the dispensing machine too fast. Some customers chase the production plan in order to speed up their production pace, thinking that the glue filling speed is adjusted too fast, so that the machine head has moved to the next position for glue filling before the glue reaches the qualified standard.
假如咱们需要加速打胶的速度调整了打胶机的移动参数的话，那么咱们对应的也应该对供胶体系也进行相应的设置，比方这时候咱们就需要加大供胶压力，增大打胶机的出胶速度来配合目标的移动速度的增加。
If we need to speed up the dispensing speed and adjust the movement parameters of the dispensing machine, we should also set the dispensing system accordingly. For example, at this time, we need to increase the dispensing pressure and the dispensing speed of the dispensing machine to match the increase of the moving speed of the target.
假如咱们仅仅是独自的增加了打胶机的移动速度而没有对压力进行调理的话就很有可能呈现打胶不丰满的状况发生。另外一种状况跟打胶机的速度差不多便是咱们的供胶压力不足导致的。
If we only increase the moving speed of the glue dispenser without regulating the pressure, it is likely that the glue is not full. The other situation is similar to the speed of the glue feeder, which is caused by insufficient glue supply pressure.
除了以上小编说的人为原因导致的这个毛病以外设备的零部件损坏也会导致这个问题，比方机头感应器损坏。
In addition to the problem caused by human factors mentioned above, the damage of equipment parts can also cause this problem, for example, the head sensor is damaged.
The reason why the gluing machine presents the flower glue and the gluing is not full is that the content explained above can be used as a reference, and more relevant precautions can be found on our website http://www.jntiannuo.com After consulting, I learned that!
上一篇：是否选购打胶机您可以从两方面思考
下一篇：双组份打胶机机头不在原位怎么调？
