双组份打胶机是专门对流体进行控制，并将流体点滴、涂覆于产品表面或产品内部的自动化机器。下面来讲讲济南双组份打胶机的主要技术参数以及结构原理。

The two-component sealant dispenser is an automatic machine that controls the fluid and drips and coats the fluid on the surface or inside of the product. Now let's talk about the main technical parameters and structural principles of the two-component sealant dispenser in Jinan.

双组份打胶机是集国内外较技术生产的中空玻璃密封胶打胶机，A组分泵和B组分泵胶分别采用系统驱动，采用无触点电器控制系统控制，换向灵敏可靠，其独特的方便可调试配比机构，较大限度地保证双组份胶近乎苛刻的配比要求，出胶连续均匀，涂胶效果好，生产效率高。

The two-component sealant applicator is a sealant applicator for insulating glass sealant produced with relatively high technology at home and abroad. The component A pump and component B pump are respectively driven by the system, controlled by the contactless electrical control system, with sensitive and reliable commutation. Its unique and convenient mixing mechanism can be debugged, which can largely ensure the strict matching requirements of two-component sealant. The sealant is continuously and evenly discharged, with good coating effect and high production efficiency.

主要技术参数：

Main technical parameters:

型号：GT04

Model: GT04

混合比：6:1-14:1

Mixing ratio: 6:1-14:1

基料桶：55加仑（20L)

Base barrel: 55 gallons (20L)

较大耗气：0.5立方米

Large gas consumption: 0.5m3

挤胶较大工作压力：20Mpa

Large working pressure of extrusion: 20Mpa

供气压力：0.5-0.8Mpa

Air supply pressure: 0.5-0.8Mpa

外形尺寸：1100*950*2500mm

Boundary dimension: 1100 * 950 * 2500mm

双组份打胶机的结构原理:

Structure and principle of two-component sealant dispenser:

双组份涂胶机由A、B胶泵、系统、升降机构、机架等组成。现分别介绍如下：

The two-component gluing machine is composed of A and B glue pumps, systems, lifting mechanisms, racks, etc. Here are the following:

1.胶泵：

1. Glue pump:

（1）A、B组份各设一个胶泵，在各自的气马达驱动下，分别作往复运动，将胶吸入并压出。A、B胶泵分别与压胶盘固定在一起，再与机架连接组成各自的系统。

(1) Each component A and B is equipped with a rubber pump, which is driven by its own air motor to perform reciprocating motion to suck in and press out the rubber. A. The rubber pump B is respectively fixed with the rubber pressing plate, and then connected with the frame to form their own systems.

（2）A、B组份的配比是通过比例杠杆进行调节：向里调节，B出胶量减少，向外调节，B出胶量增加。通过调节比例杠杆来控制B胶的出胶量，从而控制A、B胶的配比。

(2) The proportion of components A and B is adjusted through the proportional lever: inward adjustment, B glue output decreases, outward adjustment, B glue output increases. The glue output of glue B is controlled by adjusting the proportional lever, so as to control the ratio of glue A and glue B.

（3）出胶量：由气源处理器控制，逆时针调节，出胶量增加，顺时针调节出胶量减小。（这里指总出胶量）

(3) Glue output: It is controlled by the air source processor and adjusted counterclockwise to increase the glue output and clockwise to decrease it. (This refers to the total glue output)

2 . 升降机构：

2. Lifting mechanism:

A、B组份胶泵分别设一套升降机构，该升降机构分别由两个气缸并联组成，并通过横梁固定连接各自的泵体。其目的之一是将两缸的作用力通过压盘作用在胶面上，压力大小由调压阀调节，一般调整在0.3MPa左右；

A. The rubber pump of component B is respectively equipped with a set of lifting mechanism, which is composed of two cylinders in parallel, and is fixedly connected with each pump body through the beam. One of its purposes is to apply the force of the two cylinders on the rubber surface through the pressure plate, and the pressure is regulated by the pressure regulating valve, which is generally adjusted at about 0.3MPa;

其二，当需要更换胶桶时，气缸可将压盘提起。离开胶桶，以便更变新的胶桶。

Second, when the rubber bucket needs to be replaced, the cylinder can lift the pressure plate. Leave the glue bucket to change it into a new one.

打胶机的主要技术参数以及结构原理的相关内容就讲解到这里了，您对此有什么需求可以随时来我们网站http://www.jntiannuo.com咨询！

The main technical parameters and structural principles of the glue dispenser are explained here. You can come to our website at any time if you have any needs http://www.jntiannuo.com consulting service