打胶机设备常见的两个问题以及应对
自动打胶机在现代工业中起到非常重要的作用，胶水通过设备运行设定打胶出来，但是打胶机在使用的过程中会出现各种各样的情况，
济南双组份打胶机小编为大家讲解一下。
The automatic glue dispenser plays a very important role in modern industry. Glue is injected through the equipment operation settings. However, various situations will occur during the use of the glue dispenser. The small knitting machine of Jinan two-component glue dispenser will explain to you.
一、漏胶不均匀，出现花胶
1、 Glue leakage is uneven, and there is glue
1.黑胶、白胶压力是否平衡：白胶胶泵压力为0.4Mpa左右，黑胶胶泵压力不能低于0.6Mpa；2.检查比例泵黑白配比是否为1：10左右；
1. Whether the pressure of black glue and white glue is balanced: the pressure of white glue pump is about 0.4Mpa, and the pressure of black glue pump cannot be lower than 0.6Mpa; 2. Check whether the black and white ratio of the proportional pump is about 1:10;
3.检查混胶器是否安装正确与清理；
3. Check whether the rubber mixer is correctly installed and cleaned;
4.检查黑胶智能压力表参数是否正常；
4. Check whether the parameters of the black glue intelligent pressure gauge are normal;
5.检查黑胶气动开关与电磁阀动作是否正常；
5. Check whether the black glue pneumatic switch and solenoid valve operate normally;
6.检查气动开关固定块是否阻塞；
6. Check whether the fixing block of the pneumatic switch is blocked;
7.检查黑胶、白胶气动开关是否阻塞。
7. Check whether the pneumatic switches of black glue and white glue are blocked.
二、打胶不出胶
2、 Glue cannot be released
1.检查气源是否在0.60.8Mpa之间；
1. Check whether the air source is between 0.6 and 0.8Mpa;
2.检查触摸屏中编辑功能菜单中的密封不使用是否打开；
2. Check whether the seal is opened in the edit function menu of the touch screen;
3.检查气动开关是否阻塞；
3. Check whether the pneumatic switch is blocked;
4.检查黑、白胶气动开关与电磁阀动作是否正常；
4. Check whether the black and white glue pneumatic switches and solenoid valves operate normally;
5.检查比例泵上的智能压力表是否报警，范围在7-35Mpa；
5. Check whether the intelligent pressure gauge on the proportional pump alarms, and the range is 7-35Mpa;
6.检查液压站是否有压力，如无压力：1)清洗比例溢流阀2)检查比例控制器是否通电或松动；
6. Check whether there is pressure in the hydraulic station. If there is no pressure: 1) Clean the proportional overflow valve; 2) Check whether the proportional controller is energized or loose;
7.清洗时是否能出白胶，如不出再检查313胶管、旋转接头是否阻塞；
7. Check whether white glue can be released during cleaning, and if not, check whether 313 rubber tube and rotary joint are blocked;
8.检查一组比例泵下限传感器IB233是否有信号，检查二组比例泵IB407是否有信号；
8. Check whether there is signal from lower limit sensor IB233 of one group of proportional pumps and whether there is signal from IB407 of two groups of proportional pumps;
9.手动检查扫描仪数值是否有正常。
9. Manually check whether the scanner value is normal.
We have explained the two common problems of the glue dispenser and the relevant solutions. I hope we can help you. Of course, you should also maintain it during use. Pay attention to us http://www.jntiannuo.com Learn more!
上一篇：双组份打胶机平日使用注意以及应用领域
下一篇：双组份打胶机的正确打胶操作
