当涉及到打胶机时，其日常维护直接影响到打胶机的使用寿命，所以要想更为长久的顺利的使用打胶机进行工作，就要多多在平常中注意一些事项，下面小编为您解析注意事项以及应用领域。

When it comes to the glue dispenser, its daily maintenance directly affects the service life of the glue dispenser. Therefore, if you want to use the glue dispenser successfully for a longer time, you should pay more attention to some matters in daily life. The following sections will explain the matters needing attention and application fields for you.

双组份打胶机平日使用注意

Notes on daily use of two-component sealant applicator

1.由于双组份密封胶的固化需要一定时间，因此，已涂了双组份密封胶的玻璃应水平轻轻搬动。

1. As the curing of two-component sealant takes a certain time, the glass coated with two-component sealant should be moved gently horizontally.

2.A组、B组份胶应保持清洁，严防异物进入胶中。

2. Group A and B glue shall be kept clean and foreign matters shall be strictly prevented from entering the glue.

3.在连续工作过程中，胶枪每次停止工作时间一般不得超过20分钟，否则，应用A组份胶冲出全部混合胶，直单一的A组份胶从枪口排出为止。

3. In the continuous working process, the glue gun shall not stop working for more than 20 minutes each time, otherwise, all mixed glue shall be flushed out with component A glue until a single component A glue is discharged from the gun mouth.

4.高压胶管不得强行挤压、弯曲，防止影响系统正常工作。

4. The high-pressure rubber hose shall not be squeezed or bent by force to prevent affecting the normal operation of the system.

5.混胶器应经常保持畅通，以保证良好的出胶效果。如遇堵塞情况，可用丙酮浸泡后清洗。建议每5组清洗一次。

5. The glue mixer shall be kept unblocked to ensure good glue discharging effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to wash every 5 groups.

6.当胶枪长时间不用时（超过一周），应拆下枪体使用溶剂将胶枪和混胶器内的残留胶体清洗干净。

6. When the glue gun is not used for a long time (more than a week), remove the gun body and use solvent to clean the residual colloid in the glue gun and glue mixer.

7.不同双组份胶生产厂家所生产的胶内含杂质数量不同，根据实际情况清晰B组分的过滤网及单向止回阀，建议每两组清洗一次。

7. The quantity of impurities in the adhesive produced by different two-component adhesive manufacturers is different. The filter screen and one-way check valve of component B should be clear according to the actual situation. It is recommended to clean every two groups.

8.任何因胶体固化所造成的胶枪、管路或整机的故障，一律不在保修范围之内。

8. Any failure of the glue gun, pipeline or the whole machine caused by the gel curing shall not be covered by the warranty.

9.定期给各泵的加油口加油，应保证油雾器内不断油。

9. Fill the oil filler of each pump regularly to ensure that there is no oil in the oil atomizer.

双组份打胶机应用领域

Application field of two-component glue applicator

应用范围包括各种金属加工机床的零部件加工，如齿轮箱齿条的装配和维修，发动机缸体的修理以及轴承的密封和润滑等。点焊工艺中使用的胶粘剂主要有有机硅胶类和环氧树脂类两大类。

The application scope includes parts processing of various metal processing machine tools, such as assembly and maintenance of gear box and rack, repair of engine cylinder block, sealing and lubrication of bearings, etc. Adhesives used in spot welding process mainly include silicone adhesive and epoxy resin.

其中有机硅胶类的胶粘剂有热熔性橡胶型粘接剂和压敏性粘接剂两类；而环氧树脂类的胶粘剂又可分为厌氧性和氧化固化性两种类型。

Among them, there are two kinds of adhesives: hot melt rubber adhesive and pressure-sensitive adhesive; The adhesive of epoxy resin can be divided into two types: anaerobic adhesive and oxidative curing adhesive.

此外打胶机的日常维护工作对打胶机的使用寿命有很大影响，包括常用工艺的平滑度，更为详细的维护方法可以来我们网站http://www.jntiannuo.com咨询！

In addition, the daily maintenance of the glue dispenser has a great impact on the service life of the glue dispenser, including the smoothness of common processes. More detailed maintenance methods can be found on our website http://www.jntiannuo.com consulting service