讲解打胶机的安装调试过程
打胶机可简单分为,控制台,吸盘,胶头,挎板,扫描尺,打胶板。那么
双组份打胶机的安装调试过程是怎样的呢?
The glue applicator can be simply divided into console, suction cup, glue head, sideboard, scanning ruler and glue applicator. What is the installation and commissioning process of the two-component glue applicator?
打开气泵开关,电源总开关,控制台开关,在控制台按手动按钮,然后在显示屏上找到原点设定,点击辅助原点设定,然后点击头部原点设定,注意原点设定时避免头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定,先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度,输入完以后,点击设置进入。等命令位置和当前位置数值一致即可,注意设置时传送带上不要有玻璃。
Turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid the collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer strip, and then the glass thickness. After entering, click the setting to enter. Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting.
然后是混交了,按桶胶按钮,按工作选择按钮,然后按拍胶启动,在按伐开,此时胶头以出胶,等看不见白胶,以混均匀以后按伐关,在按链接生产线,自动,自动运行,此时可以自动打胶。
Then it is mixed. Press the first bucket of glue button, press the work selection button, and then press the pat glue to start. Press the cut open button, and then the glue head will release the glue. When the white glue is not visible, press the cut off button after mixing evenly. Press the link production line, and it will run automatically. At this time, it can automatically apply glue.
开始打胶要看每条边每个角打胶是否均匀,下面说下如何调整打胶机,在屏幕上点击返回找到密封配方,点击进入,会显示当前密封压力,如果每条边都缺胶,那么可增加压力,压力大胶量大,压力小胶量就小。
To start gluing, it is necessary to see whether the gluing is even at each corner of each side. Next, let's talk about how to adjust the gluing machine. Click back on the screen to find the sealing formula. Click enter, and the current sealing pressure will be displayed. If there is a lack of glue at each side, then the pressure can be increased. If the pressure is large, the amount of glue is large, and the pressure is small, the amount of glue is small.
下面说下针对某条边,或某个交,胶量不够的调试方法。在点击密封配方进入后会显示有向上密封,上部密封,向下密封,和下部密封,开始打胶的那条边就是向上密封,然后顺序从上。
The following is about the debugging method of insufficient glue for a certain edge or a certain intersection. After clicking the sealing formula to enter, it will display upward sealing, upper sealing, downward sealing, and lower sealing. The side where the glue is applied is upward sealing, and then the order is from top.
如果先打胶的这条边,打胶不均匀,那么点击向上密封,进入后显示。扫描器开后发开的时间,就是在胶嘴贴到玻璃开始移动胶嘴出胶的时间,时间长出胶晚,时间短出胶早,扫描器开后开始移动的时间,就是胶嘴移动的速度,时间长移动慢,出胶多,时间短移动快出胶少。
If the gluing is uneven on the side where the glue is applied first, click up to seal, and it will be displayed after entering. The opening time of the scanner after opening is the time when the glue nozzle starts to move when it is pasted on the glass. The longer the time, the later the glue is released, the shorter the time, the earlier the glue is released. The time when the scanner starts to move after opening is the speed of the glue nozzle. The longer the time, the slower the movement, the more the glue is released, the shorter the time, the faster the movement, and the less the glue is released.
扫描胶量细微调整,就是只有某条边胶少,或多,时调整扫描胶量细微调整,数值大胶量就大,数值小胶量就小。然后说下到末端伐关的距离,数值大,胶嘴到末端胶量少,数值小胶量大。
Fine adjustment of scanning glue amount is to adjust the scanning glue amount when there is less or more glue on a certain edge. If the value is large, the glue amount will be large, and if the value is small, the glue amount will be small. Then say the distance from the bottom to the end of the valve. If the value is large, the glue amount from the glue nozzle to the end is small, and if the value is small, the glue amount is large.
拐角时伐开的时间,就是控制拐角的胶量,数值大胶量大,数值小胶量小。如果拐角胶多就调小数值,拐角胶少,数值加大。
The cutting time at the corner is to control the glue amount at the corner. If the value is large, the glue amount is large, and if the value is small, the glue amount is small. If there is more corner glue, reduce the value. If there is less corner glue, increase the value.
Note that when adjusting the value, the value must be correct, the mixing must be uniform, and the pressure must be enough. After checking whether there is anything forgotten, wipe it clean and put it into use. For more information, please visit our website http://www.jntiannuo.com Consult and understand.
上一篇:打胶机检修小窍门必备技能
下一篇:打胶机在打胶中发生断胶解决小妙招