关于打胶机的使用，很多人都反映使用的效果很好。打胶的效果令人十分满意，那现阶段的打胶机也在不断的与时俱进的发展，不仅仅是打三玻，更能将四玻打胶。不过打胶机作为玻璃机械设备的一种，也许会发生些小问题，今儿我们就来说说打胶机的一些问题分析。

As for the use of glue applicator, many people report that the effect of use is very good. The effect of gluing is very satisfactory. At this stage, the gluing machine is also developing with the times. It can not only glue three glasses, but also glue four glasses. However, as a kind of glass mechanical equipment, the glue machine may have some small problems. Today we will talk about some problem analysis of the glue machine.

智能压力仪表：这方面可能让很多人表示惊讶，怎么会呢？这个不可能爱坏。虽然从某种意义上来说，他的使用频率不会那么高，不是工人直接接触的。但是在打胶机的供胶机上有很多的智能压力仪表，目的就是保证正常的工作进行。所以很难保证每一块智能压力表的长久良好运行。智能压力仪表的，可能要比小吸盘和定位滑轮的稍贵一点。但是因为它的损坏频率不高，所以还在大家的接受范围内。

Intelligent pressure instrument: this aspect may surprise many people. How can it be? This can't be bad. Although in a sense, his frequency of use will not be so high, it is not the direct contact of workers. However, there are many intelligent pressure instruments on the glue feeder of the glue dispenser to ensure normal operation. Therefore, it is difficult to ensure the long-term good operation of each intelligent pressure gauge. The price of intelligent pressure instruments may be slightly higher than that of small suction cups and positioning pulleys. However, because its damage frequency is not high, it is still within the range of acceptance.

小零件的损坏：打胶机的小吸盘和定位滑轮的损坏是比较常见的。通常就是单纯的由于使用工作时间过长，所以导致的损坏。这些零件在方面也是比较便宜的。

Damage to small parts: damage to the small suction cup and positioning pulley of the gluing machine is common. Usually, it is simply the damage caused by the long working time. These parts are also relatively cheap in price.

胶水流体内产生气泡：在打胶机使用期间，过大的流体压力再外部打开点胶阀时，可能将空气渗入胶水中，从而产生了气泡。

Bubbles in the glue fluid: during the use of the glue dispenser, when the dispensing valve is opened externally due to excessive fluid pressure, air may penetrate into the glue, resulting in bubbles.

打胶机使用时出现漏胶：点胶阀在使用完毕后正常关闭，出现胶水渗漏，这是因为配置的针头太小，影响液体的流动造成背压。

Glue leakage occurs when the glue dispenser is in use: the dispensing valve is normally closed after use, and glue leakage occurs, because the configured needle is too small, which affects the flow of liquid and causes back pressure.

打胶机流速太慢：胶水流速若太慢主要是胶管过窄或者过长，当然还要注意出胶口和气压是不是处于正常情况。

The flow rate of glue dispenser is too slow: if the flow rate of glue is too slow, the main reason is that the rubber hose is too narrow or too long. Of course, pay attention to whether the glue outlet and air pressure are normal.

济南双组份打胶机设备出胶量大小不一致：出胶量大小不一致的情况主要是储存胶水流体的压力筒还有机器配置空气压力不稳定所产生。

The glue output of Jinan two-component gluing machine is inconsistent: the inconsistent glue output is mainly caused by the pressure cylinder storing glue fluid and the unstable air pressure of the machine configuration.

为什么会出问题？日积月累正常的使用磨损；错误操作造成系统瘫痪等等原因，以上的故障使用者需要提前了解到，并做好相关的预防措施，更多相关内容就来我们网站http://www.jntiannuo.com咨询了解吧。

Why is something wrong? Wear and tear in normal use over time; Users of the above failures need to know in advance about the causes of system paralysis caused by incorrect operation, and take relevant preventive measures. For more relevant content, please come to our website http://www.jntiannuo.com Consult and understand.