一般情况下,能够正确的使用机器，一方面能够做好产品，另一方面也可以延长机器的使用寿命，保持机器的性能稳定持久。使用打胶机也是如此，下面简单的说明一下。

In general, being able to use the machine correctly, on the one hand, can make the product well, on the other hand, it can also prolong the service life of the machine and maintain the stability and durability of the machine. The same is true when using the glue applicator. The following is a brief description.

使用机器前，确保电源电压的稳定以及电路，保证机器在开机中正常运行。确保机器的各工件都处入原点位置，机器上没有杂物，以免阻挡机器运行，经常给机器的滑轮处加黄油，保证门窗打胶机的滑轮润滑，运转时更流畅，机器正在工作时，看看周围的人是否在的距离，以免机器在工作时伤害到旁边的人。

Before using the machine, ensure the stability of the power supply voltage and the safety of the circuit, and ensure the normal operation of the machine during startup. Make sure that all the workpieces of the machine are at the origin position, and there are no sundries on the machine, so as not to block the operation of the machine. Often add butter to the pulley of the machine to ensure that the pulley of the door and window gluing machine is lubricated and runs more smoothly. When the machine is working, check whether the people around it are at a safe distance, so as not to hurt the people next to it when the machine is working.

由于双组份密封胶的固化需要一定时间，因此，已打了双组份密封胶的玻璃应水平轻轻搬动。A组、B组份胶应保持清洁，严防异物进入胶中。在连续工作过程中，胶枪每次停止工作时间一般不得超过20分钟，否则，应用A组份胶冲出全部混合胶，直单一的A组份胶从枪口排出为止。高压胶管不得强行挤压、弯曲，防止影响系统正常工作。

Since the curing of two-component sealant takes a certain time, the glass with two-component sealant should be moved horizontally and gently. The glue of group A and B shall be kept clean to prevent foreign matters from entering the glue. In the continuous working process, the working time of the glue gun shall not exceed 20 minutes each time. Otherwise, all the mixed glue shall be washed out with component a glue until a single component a glue is discharged from the muzzle of the gun. The high-pressure rubber hose shall not be forcibly squeezed or bent to prevent affecting the normal operation of the system.

混胶器应经常保持畅通，以保证良好的出胶效果。如遇堵塞情况，可用丙酮浸泡后清洗。建议每5组清洗一次。当胶枪长时间不用时（超过一周），应拆下枪体使用溶剂将胶枪和混胶器内的残留胶体清洗干净。

The mixer should always be kept unblocked to ensure good glue output effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to clean every 5 groups. When the glue gun is not used for a long time (more than a week), remove the gun body and clean the residual colloid in the glue gun and mixer with solvent.

不同双组份胶生产厂家所生产的胶内含杂质数量不同，根据实际情况清晰B组分的过滤网及单向止回阀，建议每两组清洗一次。任何因胶体固化所造成的胶枪、管路或整机的故障，一律不在保修范围之内。定期给各泵的加油口加油，应保证油雾器内不断油。

The amount of impurities in the glue produced by different two-component glue manufacturers is different. According to the actual situation, the filter screen and one-way check valve of component B are clear. It is recommended to clean every two groups. Any failure of glue gun, pipeline or whole machine caused by colloid solidification is not within the scope of warranty. Fill the oil filler of each pump regularly, and ensure that there is continuous oil in the oil atomizer.

我们平时在使用济南双组份打胶机的时候应当注意一些问题以及保养方法，不要盲目的暴力的使用，否则很容易造成设备的损坏。以上就是相关信息了，希望给您好帮助，更多内容就来我们网站http://www.jntiannuo.com了解吧！

We should pay attention to some problems and maintenance methods when using Jinan two-component glue applicator at ordinary times. Don't use it blindly and violently, otherwise it is easy to cause damage to the equipment. The above is the relevant information. I hope you can help me. Please come to our website for more information http://www.jntiannuo.com Understand!