打胶机不出胶实际上一般分三个方面，一是供气的气泵正常，二是供气管路不漏气，三是气阀打开，这三个条件缺一不可，你可逐一检查这些方面，下面来讲讲问题吧。

In fact, the failure of the glue dispenser is generally divided into three aspects: the first is that the air pump for gas supply is normal, the second is that the air supply pipeline is not leaking, and the third is that the air valve is open. These three conditions are indispensable. You can check these aspects one by one. Let's talk about the problems below.

打胶机不出胶的原因及解决办法：

Reasons and solutions for glue failure of glue dispenser:

1，检查气源是否在0.60.8Mpa之间；

1. Check whether the air source is between 0.6 and 0.8MPa;

2，检查触摸屏中编辑功能菜单中的密封不使用是否打开；

2. Check whether the seal in the editing function menu in the touch screen is turned on when it is not in use;

3，检查气动开关是否阻塞；

3. Check whether the pneumatic switch is blocked;

4，检查黑胶气动开关与电磁阀动作是否正常；

4. Check whether the black glue pneumatic switch and solenoid valve operate normally;

5，检查比例泵上的智能压力表是否报警，范围在7-35Mpa；

5. Check whether the intelligent pressure gauge on the proportional pump alarms, and the range is 7-35mpa;

6，检查液压站是否有压力，如无压力：1）清洗比例溢流阀2）检查比例控制器是否通电或松动；

6. Check whether there is pressure in the hydraulic station. If there is no pressure: 1) clean the proportional overflow valve 2) check whether the proportional controller is powered on or loose;

7，清洗时是否能出白胶，如不出再检查313胶管、旋转接头是否阻塞；

7. Check whether white glue can be released during cleaning. If not, check whether 313 rubber hose and rotary joint are blocked;

8，检查一组比例泵下限传感器IB233是否有信号，检查二组比例泵IB407是否有信号；

8. Check whether there is a signal from the lower limit sensor ib233 of the first group of proportional pumps and whether there is a signal from the second group of proportional pumps ib407;

9，手动检查扫描仪数值是否有正常。

9. Manually check whether the scanner value is normal.

双组份打胶机出胶硅酮胶速度慢

The two-component glue applicator is slow in discharging silicone glue

使用硅酮结构密封胶时，在打胶施工现场，经常会遇到这些问题：打胶机出胶速度慢。产品在初次使用时，打胶机打胶过程中出现出胶速度过慢的现象，可能原因有三个：⑴A组分流动性差⑵压盘过大⑶气源压力不够。

When using silicone structural sealant, these problems are often encountered at the bonding construction site: the glue dispenser is slow in discharging glue. When the product is used for the first time, the glue dispensing speed of the glue dispenser is too slow during the glue dispensing process. There are three possible reasons: ⑴ poor fluidity of component a ⑵ too large pressure plate ⑶ insufficient air source pressure.

针对原因⑴或原因⑶，我们可以通过调整胶枪压力来解决；针对原因⑵，订购大口径桶可以使问题得到解决。若出胶速度慢出现在正常使用过程中，则可能是混合芯和过滤网被堵塞，一旦发现，就需要及时清理设备。

For the reason (1) or (3), we can solve it by adjusting the glue gun pressure; In view of the reason (2), ordering large-diameter barrels can solve the problem. If the glue delivery speed is slow during normal use, the mixing core and filter screen may be blocked. Once found, the equipment needs to be cleaned in time.

打胶机不出胶及出胶硅酮胶速度慢的原因便是以上了，我们都已经明确找到原因了然后就应该根据原因做预防方案了，更多信息了解就来关注我们网站http://www.jntiannuo.com吧！

The reason why the glue applicator does not produce glue and the speed of silicone glue is slow is the above. We have clearly found the reason, and then we should make preventive plans according to the reason. For more information, please pay attention to our website http://www.jntiannuo.com Come on!