Working principle of two-component automatic glue applicator: the double liquid glue dispenser consists of two pressure buckets (storing a and B glue and controlling the glue delivery ratio of a and B glue by adjusting the pressure in the pressure bucket), and one is the glue dispenser controller (controlling the glue dispensing time and interval by controlling the action of the glue dispensing valve), 1 double liquid dispensing valve (the dispensing machine controls the action of the valve body to control the glue output, and can fine tune the glue output ratio of a and b). Glue a and B are respectively connected from the glue outlet of the pressure barrel to the glue inlet a and B of the dispensing valve. After passing through the tee, the glue a and B flowing out of the dispensing valve begin to mix in the static mixing pipe, and are continuously and repeatedly cut by the wavy block in the mixing pipe to fully stir the two kinds of glue and flow out after mixing evenly.

双组份自动打胶机主要适用于:

The two-component automatic glue applicator is mainly applicable to:

LED灯条的灌胶、灯具、水晶工艺品的灌胶、电子点火器、高频变压器的灌胶封装、离子发生器的灌封、充电器的灌胶、手机按键点胶、手机电池封装、笔记本电池封装、线圈点胶、IC 封胶、喇叭外圈点胶、 PDA 封胶、 LCD 封胶、机壳粘接等电子产品加工、光学器件加工、机械密封等应用。

Glue filling of LED light strip, energy-saving lamps, crystal crafts, electronic igniter, glue filling and packaging of high-frequency transformer, ion generator, charger, mobile phone key dispensing, mobile phone battery packaging, notebook battery packaging, coil dispensing, IC sealing, horn outer ring dispensing, PDA sealing, LCD sealing, casing bonding and other electronic product processing Optical device processing, mechanical sealing and other applications.

主要部件介绍：

Introduction to main components:

1、微电脑控制的数显点胶机控制器：使点胶精度更精确，并且有自动，定量和循环等多种操作模式。数字按钮设定、LED显示时间、直观、方便。循环点胶功能，可实现自动化流水生产线间隔所需时间自动点胶。

1. Microcomputer controlled digital display dispenser controller: it makes the dispensing accuracy more accurate, and has a variety of operation modes such as automatic, quantitative and circulation. Digital button setting, LED display time, intuitive and convenient. The circulation dispensing function can realize the automatic dispensing at the interval required by the automatic flow production line.

2、精密双液点胶阀：由点胶机控制出胶，点胶阀尾部调节螺丝和胶水的压力可控制出胶量大小。调节螺丝顺时钟向下转动为减小胶量，逆时钟方向转动为 加大胶量。

2. Precision double liquid dispensing valve: the dispensing is controlled by the dispensing machine. The amount of glue can be controlled by adjusting the pressure of screw and glue at the tail of the dispensing valve. Turn the adjusting screw clockwise to reduce the glue amount, and counterclockwise to increase the glue amount.

3、静态混合管的混合方式为静态混合，由一连串左右旋叶片相互垂直排列在套管内组成，A、B胶水经过静态混合管时进行连续的切割与重合为均匀的混合液。静态混合管出口部可接任何口径的针头，以保证出胶量精确。混合管可重复使用，工作结束后拔掉混合管并将之泡在丙酮，酒精，天那水等溶剂里进行清洗，下次工作可继续使用。

3. The mixing mode of the static mixing pipe is static mixing, which is composed of a series of left and right rotating blades vertically arranged in the casing. When a and B glue pass through the static mixing pipe, they are continuously cut and overlapped to form a uniform mixing liquid. The outlet of the static mixing tube can be connected with a needle of any caliber to ensure accurate glue output. The mixing tube can be reused. After the work, pull out the mixing tube and soak it in acetone, alcohol, Tianna water and other solvents for cleaning. It can be used again in the next work.

4、2个压力桶：胶水分装，长时间不固化。通过调节两个压力桶的气压，可以方便地调节胶水的出胶比例在1：13：1。对流动性差、粘稠度大的胶水可选装加热装置，确保胶水有较好的流动性。对于长时间放置会沉淀的胶水可根据需要加装手动、电动搅拌功能。压力桶材质有不锈钢和碳钢可选。

4. 2 pressure drums: glue is sub packed and does not solidify for a long time. By adjusting the air pressure of the two pressure barrels, the glue output ratio can be easily adjusted from 1:1 to 3:1. Heating device can be selected for glue with poor fluidity and high viscosity to ensure good fluidity of glue. For glue that will precipitate after a long time, manual and electric mixing functions can be added as needed. The pressure barrel is made of stainless steel and carbon steel.

5、压力桶的清洗方便快捷，并可根据用户的需要可另配置不锈钢内胆。将压力桶内的胶水换成清洗液（清水/天那水/酒精/丙酮），高压力将清洗液从胶枪打出，可胶枪内残余胶。在常温下分装在A、B压力桶内的胶水如不固化或沉淀，工作结束后无需清理

5. The cleaning of the pressure barrel is convenient and fast, and the stainless steel liner can be configured according to the needs of users. Replace the glue in the pressure barrel with cleaning fluid (clean water / Tianna water / alcohol / acetone), and shoot the cleaning fluid from the glue gun under high pressure to remove the residual glue in the glue gun. If the glue sub packed in pressure drums A and B at normal temperature does not solidify or precipitate, it does not need to be cleaned after the work is completed