1. In the automatic two-component gluing machine, the general use of glue is about silica gel, instant glue, anaerobic adhesive, epoxy resin, UV glue.

2、真空回吸阀必需求安装在全自动点胶机上，因为真空回吸功用是防止点胶机中的胶水在不点胶时还在滴漏。

2. The vacuum suction valve must be installed on the automatic dispenser, because the vacuum suction function is to prevent the glue in the dispenser from dripping when not dispensing.

3、点胶量的巨细是由全自动双组份打胶机在点胶进程中继续的时间长短来抉择的，可以确保有满意的胶水来粘合部件，一同可以防止胶水过多而形成的资源糟蹋。

3. The size of the dispensing amount is determined by the length of time that the automatic two-component dispenser continues in the dispensing process, which can ensure that there is satisfactory glue to bond the parts, and can prevent resource waste caused by excessive glue.

4、固化要素：关于胶水的固化，一般出产厂家已给出温度曲线。一般在常温下都可以固化，在实践应尽可能选用较高温度来固化，使胶水固化后有满意强度和硬度。

4. Curing elements: about the curing of glue, the general manufacturer has given the temperature curve. Generally, it can be cured at normal temperature. In practice, higher temperature should be selected as far as possible to make the glue have satisfactory strength and hardness after curing.

5、针头的标准与类别：针头的标准会影响点胶机在点胶进程中出胶的巨细和精密度,当气压在必定规划时，针头的咀越大,出胶率就越大，所以要依据点胶机在出产出来产品的巨细来定位点胶针头的标准，一般针头内径长度保持在胶点直径的一半,作用才是更好。

5. Standard and category of needle: the standard of the needle will affect the size and precision of the dispensing machine in the dispensing process. When the air pressure is in a certain planning, the larger the nozzle of the needle is, the greater the glue output rate will be. Therefore, it is necessary to locate the dispensing needle standard according to the size of the product produced by the dispenser. Generally, the inner diameter of the needle should be kept at half of the diameter of the glue point.

6、气泡关于全自动双组份打胶机在进行点胶进程中会影响产品质量，所以胶水放进去之前决对不能有气泡.如果有气泡就会形成点胶机出产出来的产品有许多次品，在运用中要排出胶水的空气，以防止出现全自动点胶机空打现象。

6. Bubble about the full-automatic two-component dispenser in the dispensing process will affect the product quality, so there must be no bubble before the glue is put in. If there are bubbles, there will be many defective products produced by the dispenser. During the operation, the air of glue should be discharged to prevent the phenomenon of empty tapping of automatic dispensing machine.

7、压力的巨细直接影响了供胶量和胶水流出的速度,胶水的流动性越差它就越稠，全自动双组份打胶机需求的压力就越大，所以咱们应该依据全自动点胶机在出产进程中的环境温度以及点胶量的巨细和胶水的特性来调度压力的巨细，全自动点胶机的压力巨细是经过它内部的调压阀来进行调度的。

7. The size of the pressure directly affects the amount of glue supplied and the speed of glue outflow, The worse the fluidity of the glue, the thicker it will be, and the greater the pressure required by the automatic two-component gluing machine. Therefore, we should adjust the pressure according to the ambient temperature of the automatic dispenser in the production process, the size of the dispensing amount and the characteristics of the glue. The pressure of the automatic dispenser is regulated through its internal pressure regulating valve.