1. Because the solidification of the two-component sealant requires a certain time, the glass coated with the two-component sealant should be moved gently and horizontally.

2.A组、B组份胶应坚持清洁，严防异物进入胶中。

Group 2.A and B components should be kept clean and strictly prevented from entering the glue.

3.在接连作业过程中，胶枪每次中止作业时刻一般不得超越20分钟，不然，运用A组份胶冲出悉数混合胶，直单一的A组份胶从枪口排出停止。

3. In the process of continuous operation, the gun should not stop operation more than 20 minutes each time. Otherwise, use component A glue to punch out all the mixed glue until a single component A glue is discharged from the muzzle to stop.

4.高压胶管不得强行揉捏、曲折，避免影响体系正常作业。

4. high pressure hose should not be forced to knead, twists and turns, to avoid affecting the normal operation of the system.

5.混胶器应常常坚持疏通，以确保杰出的出胶作用。如遇阻塞状况，可用丙酮浸泡后清洗。主张每5组清洗一次。

5. rubber mixer should be constantly dredged to ensure excellent glue production. In case of obstruction, acetone can be soaked and cleaned. It is advocated that every 5 groups be cleaned once.

6.当胶枪长时刻不用时（超越一周），应拆下枪体运用溶剂将胶枪和混胶器内的残留胶体清洗洁净。

6. When the gun length is not used at all times (more than a week), the gun should be removed and the residual colloid in the gun and mixer should be cleaned by solvent.

7.不同双组份胶出产厂家所出产的胶内含杂质数量不同，依据实际状况明晰B组分的过滤网及单向止回阀，主张每两组清洗一次。

7. Different two-component glue manufacturer produces different amount of impurities in the glue, according to the actual situation clear B component filter screen and one-way check valve, advocate cleaning every two groups.

8.任何因胶体固化所造成的胶枪、管路或整机的毛病 双组份打胶机，一概不在保修规模之内。

8. Any defect caused by gel solidification in the rubber gun, pipeline or the whole machine, how much is the two-component glue beater, is not within the scope of warranty.

9.定时给各泵的加油口加油 中空双组份打胶机，应确保油雾器内不断油。

9. regularly fill the filling ports of each pump with a hollow two component glue machine, and ensure that the oil mist is constantly oil.

双组份打胶机的结构原理:

The structure principle of two component rubber beating machine:

双组份涂胶机由A、B胶泵、气动体系、升降组织、机架等组成。现别离介绍如下：

The two component glue dispenser is composed of A, B glue pump, pneumatic system, lifting structure, rack and so on. The following are the following:

1.胶泵：

1. glue pump:

（1）A、B组份各设一个胶泵，在各自的气马达驱动下，别离作往复运动，将胶吸入并压出。A、B胶泵别离与压胶盘固定在一起，再与机架衔接组成各自的体系。

(1) Components A and B are equipped with a rubber pump, driven by their respective gas motors, separately reciprocating movement, will be glue inhalation and pressure out. The A and B rubber pumps are separated from the pressure plate and connected to the rack to form their own system.

（2）A、B组份的配比是经过份额杠杆进行调理：向里调理，B出胶量削减，向外调理，B出胶量添加。经过调理份额杠杆来操控B胶的出胶量，从而操控A、B胶的配比。

(2) The proportion of A and B components is regulated by share lever: inward conditioning, B glue reduction, outward conditioning, B glue added. After adjusting the share lever to control the gel output of B glue, the ratio of A and B glue is controlled.

（3）出胶量：由气源处理器操控，逆时针调理，出胶量添加，顺时针调理出胶量减小。（这儿指总出胶量） 本胶泵经过份额杠杆调理A、B胶量配比，具有操作灵敏，功能安稳，调理规模大等特点。

(3) glue yield: controlled by air source processor, counterclockwise conditioning, glue yield added, clockwise conditioning glue yield decreased. (hereinafter referred to as the total amount of glue) the rubber pump through the share of lever adjustment A, B glue ratio, with a sensitive operation, stable function, large-scale conditioning and other characteristics.

2 . 升降组织：

2. lifting organization:

A、B组份胶泵别离设一套气动升降组织，该升降组织别离由两个气缸并联组成，并经过横梁固定衔接各自的泵体。其意图之一是将两缸的作用力经过压盘作用在胶面上，压力巨细由调压阀调理，一般调整在0.3MPa左右；

Component A and B rubber pumps are separated by a set of pneumatic lifting organizations, which are composed of two cylinders in parallel, and connected with each other through a fixed beam. One of its intentions is to force the two cylinders on the glue surface through the pressure plate, the pressure is regulated by the pressure regulating valve, generally adjusted to about 0.3 MPa;

其二，当需求替换胶桶时，气缸可将压盘提起。离开胶桶，以便替换新的胶桶。

Second, when the need to replace the plastic bucket, the cylinder can lift the pressure plate. Leave the plastic bucket to replace the new plastic bucket.