点胶机的工作流程详解！
接上220V电源，0.5MPA气源并查看以下内容：
Connect 220V power supply, 0.5MPA air source and check the following contents:
1.胶水储量：查看AB储料罐要有足够的胶水；
1. Glue storage: check AB storage tank to have enough glue;
2.加热拌和及真空脱泡：如需要加热，一般不要加热A料，直接加热B料即可，加热的时分必须翻开拌和；相同如真空脱泡，需翻开抽真空阀门，此进程需在第3步之前完成。
2. Heating mixing and vacuum defoaming: If heating is needed, generally do not heat material A, directly heating material B, heating time must be turned over mixing; the same as vacuum defoaming, vacuum valve should be opened, this process needs to be completed before step 3.
3.点胶机阀门状况：先翻开进气阀（出胶压力来历），然后翻开出料阀，预留抽真空阀门封闭；测验吐胶阀门，看阀门是否灵敏；
3. Valve condition of dispensing machine: first turn on the intake valve (the origin of the dispensing pressure), then turn on the discharge valve, reserve the vacuum valve to close; test the dispensing valve to see if the valve is sensitive;
4.测验及发动：
4. Testing and initiation:
a）测验吐胶阀门，看阀门是否灵敏；
(a) Testing the gum-spitting valve to see if it is sensitive;
b）触摸屏一体机设置好AB胶的出胶比例，按屏摸屏中的发动按钮，设备开始作业；
B) The touch screen integrative machine sets the proportion of AB glue, press the start button in the touch screen, and the equipment starts to work.
（二）点胶机点胶进程
(2) Dispensing process of dispensing machine
1、混合后的胶水：
1. Mixed glue:
a）外观：混合好的胶水应该是均匀一致的
Appearance: Mixed glue should be uniform.
b）分量：单次吐胶总量应该一致
B) Component: The total amount of single spitting should be the same.
注：点胶机若呈现显着不均匀或分量不一致，请停机查看
Note: If dispensing machine shows significant non-uniformity or inconsistent components, please stop and check.
建议：出产进程中，每做一定数量的产品，重新核定一次胶水总量
Suggestion: In the production process, the total amount of glue should be re-checked once for every certain quantity of products.
2、气压过低报警灯：当气压低于作业气压后，发出蜂鸣报警声，需停止吐胶，待气压恢复蜂鸣停止报警后，正常出产。
2. Low air pressure alarm lamp: When the air pressure is lower than the working pressure, buzzing alarm sounds are emitted. It is necessary to stop spitting gum. After the buzzing stop alarming when the air pressure is restored, normal production will occur.
3、留意调查A/B料液位显示管，作好加料预备。
3. Investigate the level display tube of A/B material carefully and prepare for feeding.
4、在灌封时呈现导常是按急停键：
4. Press the emergency stop key when filling.
按下急停按钮，机器将不吐出胶水；当急停按钮松开弹起时，机器吐出胶水。
Press the emergency stop button, the machine will not spit out glue; when the emergency stop button is released and popped up, the machine spits out glue.
（三） 点胶机的点胶完毕
(3) The dispensing of dispensing machine is completed
1、封闭加热，拌和，触摸屏按钮按下“停止”键
1. Closed heating, mixing, touch screen button press "stop" key
2、静态混合管清洗：停止吐胶后必须在短时间之内拆开并清洗混合管，避免凝结造成堵塞。
2. Static mixing pipe cleaning: After stopping spitting, the mixing pipe must be dismantled and cleaned in a short time to avoid clogging caused by condensation.
3、拆开混合管安装密封盖：在密封盖里装入三分之一的黄油，旋上即可密封。
3. Dismantle the mixing pipe and install the sealing cap. Install one third of the butter in the sealing cap, and it can be sealed by screwing.
4、点胶机封闭阀门：封闭料桶进气阀（干燥剂阀门）
4. Closed valve of dispensing machine: Closed material barrel intake valve (desiccant valve)
5、封闭点胶机电源气源
5. Power Supply of Closed Dispenser
The above is the working process of dispenser. More information can continue to focus on our website: http://www.jntiannuo.com.
上一篇：中空玻璃打胶机的作用怎么样？
下一篇：点胶机设备的受什么因素的影响？
