你现在的位置:首页>企业动态

介绍中空玻璃打胶机怎么操作!

浏览:0
  关于中空玻璃主动打胶机小编现已和我们说了很多,比如关于职业额发展、整体的现状,还有和中空玻璃相关职业的知识等等。可是小编发现很多的读者在私信小编时问的都是有关于中空玻璃主动打胶机的根底操作等相关问题。今天小编就和我们清清楚楚的说清楚关于中空玻璃主动打胶机的调整与操作的问题。
  We have talked a lot about the small edition of the active gluing machine for hollow glass, such as the professional development, the overall status quo, as well as the knowledge of hollow glass related professions and so on. However, Xiaobian found that many readers in private trust Xiaobian asked about the basic operation of the hollow glass active gluing machine and other related issues. Today, Xiaobian and we clearly explained the adjustment and operation of the active gluing machine for hollow glass.
  中空玻璃主动打胶机
  Hollow glass active glue machine
  操作流程:
  Operation procedure:
  1、 放在一个平整洁净的平面上,连接电源和气源,两者承认接通之后就开始进行操作。
  1. Place it on a flat and clean surface, connect the power supply and the air source, both of which admit to start operation after the connection.
  2、 打胶机中间会有一个混胶过程,在供胶机上面混胶完毕之后,需要在电子显示屏上控制面板上进行挑选“行走设置”。翻开界面之后按T1键前进行走。在机头中止时,翻开机头上面B胶阀门,接着在控制面板上找到Esc键回来主界面,然后F2状态设置,在翻开界面后按K3键供胶开始,当胶嘴中完全混合的胶流出按K4键完毕供胶。
  2. There will be a mixing process in the middle of the glue beater. After mixing is finished on the glue feeder, it is necessary to select "walking settings" on the control panel of the electronic display screen. After opening the interface, press T1 button to move forward. When the nose stops, turn on the B glue valve above the nose, then find the Esc key on the control panel to return to the main interface, then set F2 status, press K3 key to start gluing after opening the interface, and press K4 key to finish gluing when the completely mixed glue in the nozzle flows out.
  3、 需要记住的是工作完毕之后或者在较长时间不工作时,需要冲洗混胶装置,避免供胶管的阻塞,影响未来运用作用。
  3. It should be remembered that after the completion of the work or after a long period of non-work, it is necessary to flush the mixing device to avoid the obstruction of the rubber supply pipe, which will affect the future application.
双组份打胶机
  4、 调整环节:吸盘调整:涂胶机吸盘与旋转台的高度调整合适。
  4, adjustment link: sucker adjustment: the height adjustment of the suction machine and the rotary table of the glue dispenser is suitable.
  5、 气动开关、胶嘴、探针调整:将事前合好的中空玻璃放在旋转台上,靠近涂胶机工作面,然后中空玻璃推到定位上,调整胶嘴与玻璃的高度,使出胶嘴的出胶口中心于铝槽中心在同一个水平线上:胶嘴与玻璃之间的顶力合适:铝槽深度检测探针与出胶口中心线在统一水平线上。
  5. Pneumatic switch, glue nozzle and probe adjustment: place the hollow glass on the rotary table, close to the working face of the glue coating machine, then push the hollow glass to the position, adjust the height of the glue nozzle and the glass, so that the glue outlet center of the glue nozzle is on the same horizontal line at the center of the aluminium groove: the top force between the glue nozzle and the glass is appropriate. The depth probe of aluminum groove and the center line of the rubber outlet are at the same level.
  6、 发动开关(机头的前端的光开关)与玻璃之间的检测间隔(1.5~2mm)。在控制面板上挑选“状态设置”,翻开状态设置后挑选“吸盘开(K5键)”,此时机头会往前移动,假如不往前移动则检查并调整发动开关的检测间隔。
  6, the detection interval (1.5~2mm) between the starting switch (the optical switch at the front end of the nose) and the glass. Select "state setting" on the control panel and "sucker opening" (K5 key) after turning on the state setting. At this time, the nose will move forward. If it does not move forward, check and adjust the detection interval of the start switch.

上一篇:自动打胶机和手动打胶机的区别有哪些?
下一篇:教你灌胶机的保养方法!

  • 微信