双组份打胶机的当天使用完毕的事项
1、在当天机器操作完毕后要把胶管内的胶冲出,防止硬化;如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the operation of the machine on that day, the glue in the hose should be punched out to prevent hardening; if it is not practical for a long time, it should be noted to clean the hose and gun with kerosene.
2、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高,低质量的胶容易堵塞胶管的过滤系统,造成出胶不畅或不均匀。
2. The silicone glue or polysulfide glue used in the two-component beater should pay attention to the impurities can not be too high, low-quality glue is easy to plug the rubber pipe filtration system, resulting in unsmooth or uneven glue.
3、在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净,好清洗,因为不同品种甚的胶容易反应堵塞机器。
3. When replacing the type of glue, special attention should be paid to the two-component glue beater to wash the residual glue, the best cleaning, because different varieties or even brands of glue easily react to block the machine.
4、液压站系统的压力,不能调的太高,要根据室内环境温度等实际情况,调满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪,否则B组份管路压力将升得很高,造成事故。
4. The pressure of the hydraulic station system can not be adjusted too high, according to the indoor environment temperature and other actual conditions, adjust to meet the normal rubber nozzle glue evenly. Must open the glue gun when opening the hydraulic station, otherwise the pressure of B component pipeline will rise very high, causing safety accidents.
5、A胶提胶泵连续工作1分钟以上没有供胶停止,说明管路内有空气,此时会报警,须打开泵上管接头再打开A胶提胶泵,直到出胶为止,停止并接好接头,胶枪会出现有空气的哔哔爆破声,空气排净就好了。
5. A glue pump working continuously for more than one minute without ceasing glue supply, indicating that there is air in the pipeline, at this time will alarm, to open the upper pipe connector of the pump and then open the A glue pump, until the glue is out, stop and connect the connector, the glue gun will appear to have the air beep explosion sound, air drain is good.
6、硅酮胶B 组份遇空气会结壳,影响泵的正常工作和管路的畅通,因此,停机时B组份胶的所有通道在泄压后均应关闭,使B组份不得接触空气。
6. Component B of silicone glue will crust when it meets the air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B glue should be closed after pressure relief, so that component B can not touch the air.
7、正常工作时不要断气源,如果发现断气源应停止工作。
7, do not interrupt the source of gas when working normally. If you find the source of gas, you should stop working.
本文的精彩内容来自:
双组份打胶机更多的详细内容请点击我们的网站:
http://www.jntiannuo.com谢谢您的到来
The highlights of this article come from: For more details on the two-component dispenser, please click on our official website:
http://www.jntiannuo.com. Thank you for coming.
上一篇:双组份打胶机自身特点带来的使用优势
下一篇:真空灌胶机的这些特点你知道吗?