1, the vent valve on the pressure plate should be kept open and regularly dredged and cleaned.

2、正常工作时不要断气源，如果发现断气源应停止工作。

2, do not interrupt the source of gas when working normally. If you find the source of gas, you should stop working.

3、若涂胶工作过程中停顿时间超过15分钟以上时，一定要用“冲枪”。本机有报警功能，到时没有冲胶会有蜂鸣器报警。

3. If the pause time is more than 15 minutes in the process of gluing, you must use the "punch gun". This machine has alarm function. When there is no glue, there will be a buzzer alarm.

4、定期检查气源，应保证使用经干燥的洁净压缩空气，并定期排放分离过滤器中的积水，检查油雾器中的油是否够用。

4. Regular inspection of the gas source, first of all, should ensure the use of dry clean compressed air, and regular discharge of separation filter water, check whether the oil mist is enough.

5、硅酮胶B 组份遇空气会结壳，影响泵的正常工作和管路的畅通，因此，停机时B组份胶的所有通道在泄压后均应关闭，使B组份不得接触空气。

5. Component B of silicone glue will crust when it meets the air, which will affect the normal operation of the pump and the smooth flow of the pipeline. Therefore, all channels of component B glue should be closed after pressure relief, so that component B can not touch the air.

6、B胶桶内如果要有空气，空气将排不出来，B泵将快速往返运动，不能向高压泵内正常供胶，影响整个系统，因此，必须将空气排出来。方法是：将压盘提出从新压入并放气。

6. If there is air in the B glue bucket, the air will not be exhausted, and the B pump will move back and forth quickly. It can not supply glue to the high-pressure pump normally, affecting the whole system. Therefore, the air must be discharged. The method is to press the pressure plate forward and deflate.

7、液压站系统的压力，不能调的太高，要根据室内环境温度等实际情况，调满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪，否则B组份管路压力将升得很高，造成事故。

7. The pressure of the hydraulic station system can not be adjusted too high, according to the indoor environment temperature and other actual conditions, adjust to meet the normal rubber nozzle glue evenly. Must open the glue gun when opening the hydraulic station, otherwise the pressure of B component pipeline will rise very high, causing safety accidents.

8、A胶提胶泵连续工作1分钟以上没有供胶停止，说明管路内有空气，此时会报警，须打开泵上管接头再打开A胶提胶泵，直到出胶为止，停止并接好接头，胶枪会出现有空气的哔哔爆破声，空气排净就好了。

8. A glue pump continuous work for more than 1 minute without glue supply stop, indicating that there is air in the pipeline, at this time will alarm, must open the upper pipe connection of the pump and then open the A glue pump, until the glue out, stop and connect the joint, the glue gun will appear air beep explosion sound, air drain is good.

9、由于每次冲洗混合器不会完全干净，每次都有少量的混合胶沉积，越来越多，以致堵塞混合器通道，用一段时间后，影响出胶量和混合效果，因此要定期（聚硫胶五天，硅酮胶两天）清洗混合器。把混合器内的混胶棒拆出，如有损坏更换新的混胶棒。若混胶棒拆不出来，可用火烧掉，注意不能损伤零件螺纹。

9. Because the mixer will not be completely clean every time, each time there is a small amount of mixed glue deposition, more and more, resulting in blocking the mixer channel, after a period of time, affecting the amount of glue and mixing effect, so regularly (polysulfide five days, silicone two days) to clean the mixer. Disassemble the mixing stick in the mixer and replace the new mixing stick if there is any damage. If the mixing stick can not be removed, it can be burnt down. Attention must not be given to screw threads.

本文由双组份打胶机提供技术支持，更多的详细精彩内容请点击我们的网站http://www.jntiannuo.com我们将会全心全意为您提供满意的服务。

This article is supported by a two-component dispenser. For more details, please click on our official website http://www.jntiannuo.com. We will provide you with satisfactory service wholeheartedly.