操作简单的双组份打胶机有9个方面要注意
双组份打胶机控制体系选用PLC和触屏，人机界面，一键式操作。设备操作简单，方便。厂家告诉大家，操作简单的双组份打胶机有9个方面要注意！
The control system of two-component rubber beater adopts PLC and touch screen, man-machine interface and one key operation. The equipment is simple and convenient to operate. The manufacturer told us that there are 9 aspects to pay attention to for the simple two-component sealant dispenser!
1.由于双组份打胶机的固化需求必定时刻，因此，已涂了双组份密封胶的玻璃应水平轻轻搬动。
1. As the curing demand of two-component sealant applicator is certain, the glass coated with two-component sealant should be moved gently horizontally.
2.A组、B组份胶应保持清洁，严防异物进入胶中。
2. Group A and B glue shall be kept clean and foreign matters shall be strictly prevented from entering the glue.
3.在连续作业过程中，胶枪每次停止作业时刻一般不得超越20分钟，不然，运用A组份胶冲出全部混合胶，直单一的A组份胶从枪口排出为止。
3. In the process of continuous operation, the glue gun shall not be stopped for more than 20 minutes each time, otherwise, all the mixed glue shall be flushed out with component A glue until a single component A glue is discharged from the muzzle of the gun.
4.高压胶管不得强行挤压、弯曲，避免影响体系正常作业。
4. The high-pressure rubber hose shall not be squeezed or bent by force to avoid affecting the normal operation of the system.
5.混胶器应常常保持畅通，以确保良好的出胶效果。如遇阻塞状况，可用丙酮浸泡后清洗。建议每5组清洗一次。
5. The glue mixer should always be kept smooth to ensure good glue discharging effect. In case of blockage, it can be cleaned after soaking in acetone. It is recommended to wash every 5 groups.
6.当胶枪长时刻不用时(超越一周)，应拆下枪体运用溶剂将胶枪和混胶器内的残留胶体清洗干净。
6. When the glue gun is not used for a long time (more than one week), remove the gun body and use solvent to clean the residual colloid in the glue gun and glue mixer.
7.不同双组份打胶机生产厂家所生产的胶内含杂质数量不同，依据实际状况清晰B组分的过滤网及单向止回阀，建议每两组清洗一次。
7. The quantity of impurities in the glue produced by different two-component sealant manufacturers is different. It is recommended to clean the filter screen and one-way check valve of component B according to the actual situation.
8.任何因胶体固化所形成的胶枪、管路或整机的毛病，一律不在保修范围之内。
8. Any defects of the glue gun, pipeline or the whole machine caused by the gel curing are not covered by the warranty.
9.定期给双组份打胶机的各个泵的加油口加油，应确保油雾器内不断油。
9. Fill the oil filler of each pump of two-component sealant dispenser regularly to ensure that there is no oil in the oil atomizer.
The two-component gluing machine is stable and reliable with high production efficiency. When using the two-component sealant machine, pay attention to the above matters. Come to our website for more information http://www.jntiannuo.com Consult!
上一篇：几点关于双组份打胶机的点胶知识要点
下一篇：打胶机工作完后中空胶固化慢怎么回事
