自动打胶机分别配置多头跟单头的原因您了解吗？实际上这个问题应该进行分析，有利于在后期的使用设备工作顺顺利利，下面济南双组份打胶机厂家为您讲解一番吧。

Do you understand the reason why the automatic gluing machine is equipped with multiple heads and single heads? In fact, this problem should be analyzed, which is conducive to the smooth operation of the equipment in the later stage. The Jinan two-component glue machine manufacturer will explain it for you.

选用多头灌胶的原因：多头同时灌胶，即可省去三轴走位的时间，假如A设备使用一个头灌胶，B设备使用四个头灌胶，那么B设备可以省去三次三轴走位时间，如果生产两万的产品，那么省下的时间可以被使用在生产更多的产品上面。

Reasons for selecting multiple heads for glue filling: if multiple heads are used for glue filling at the same time, the time for three-axis movement can be saved. If equipment a uses one head for glue filling and equipment B uses four heads for glue filling, then Equipment B can save three times of three-axis movement time. If 20000 products are produced in a day, the saved time can be used to produce more products.

多头灌胶，其实就是使用分流器将一个出胶头的胶水量进行分开灌注。那么需要分流的时候，就会造成误差。正负0.1克的误差便会提高。某些厂商对于精度要求没那么高，即便多个0.2克左右胶水，也无伤大雅，但如果追求精度，此时便不可以使用多头灌胶了。

Multi head glue filling is actually to use a shunt to separate the glue amount of one glue outlet. Then when it is necessary to shunt, it will cause errors. An error of plus or minus 0.1 g is increased. Some manufacturers do not have such high requirements for accuracy. Even if more than 0.2g glue is used, it is not harmful. However, if the accuracy is pursued, it is not allowed to use multiple glue filling at this time.

选用单头灌胶的原因：既然多头灌胶对于节约时间如此有用，为何还要选用单头灌胶呢？不同的厂商会有不同的灌胶需求。某部分厂商产品的灌胶量特别少，可能在0.5或者0.3克左右，那么此时对于精度要求就特别高，再使用多头灌胶就不适合了。

Reason for choosing single head glue filling: since multi head glue filling is so useful for saving time, why choose single head glue filling? Different manufacturers have different glue filling requirements. The glue filling amount of some manufacturers' products is very small, which may be about 0.5 or 0.3 g. at this time, the accuracy requirements are particularly high, and it is not suitable to use multiple glue filling.

多头灌胶之多头分别控制的打胶机：打胶机分别配置多头跟单头，这个功能无需额外增添费用，只需要跟厂家提供一下需求，自会配备多头或单头出胶头随机器一起出厂。

Multi head gluing machine controlled by multiple heads: the gluing machine is equipped with multiple heads and single heads respectively. This function does not require any additional cost. It only needs to provide the manufacturer with the requirements, and will be equipped with multiple heads or single head gluing heads to leave the factory with the machine.

但如果是，需要分别控制多个头的灌胶设备，那么这个需要增添不同的配置。假如配备了四个头，而这四个头都是可以使用按钮分别控制的，也就是可以分别一个，两个，三个，四个分别或同时出胶水，而是分别为出胶水头配置泵体，分别计量与控制每个出胶头的胶水量，从而达到多头控制的效果，使用分流器进行分流多头灌胶，则只有同时出胶或不出胶，不能分别控制。

However, if it is necessary to separately control the glue filling equipment of multiple heads, then different configurations need to be added. If there are four heads, and these four heads can be controlled by buttons, that is, one, two, three, four can be used to dispense glue separately or at the same time. Instead, the pump body is configured for the glue dispensing head to measure and control the glue amount of each glue dispensing head respectively, so as to achieve the effect of multi head control. If the diverter is used to dispense glue from multiple heads, the glue can be dispensed at the same time or not, and cannot be controlled separately.

自动打胶机分别配置多头跟单头的原因就是这样了，此外操作者要在使用设备之前提前去预防问题，更多事项就来我们网站http://www.jntiannuo.com咨询了解吧。

This is the reason why the automatic gluing machine is equipped with multiple heads and single heads. In addition, operators should prevent problems before using the equipment. For more information, please visit our website http://www.jntiannuo.com Consult and understand.