关于打胶机有几个常出现的问题要了解
打胶机在上下行程的时候出现混胶不匀，白胶多的问题？
The problem of uneven glue mixing and too much white glue in the up and down strokes of the glue applicator?
这个是压力桶的内压过高导致，没封闭好，解决方法是尽量不要使用带内压的胶桶施工，这个工艺太古老了。可以选择齿轮泵抽压方式，稳定，出胶量平衡性好，而且不会带有内压。带内压的都需要施工工人很仔细，否则麻烦多多.
This is caused by the high internal pressure of the pressure bucket, which is not closed well. The solution is to try not to use the rubber bucket with internal pressure for construction. This process is too old. Gear pump pumping mode can be selected, which is stable, with good balance of glue output and no internal pressure. Those with internal pressure need the construction workers to be very careful, otherwise there will be a lot of trouble
打胶机出胶比原来细和少？
Is the glue output of the glue dispenser thinner and less than the original?
打胶机出胶比原来细如果您的胶枪，混胶器都用煤油清理了还这样的话，需要检查：看看现在用的胶（看白胶就可以）是不是比以前的胶硬，同样的压力，硬的胶比稀的胶出胶量小；打胶机的压力是不是正常（气源压力，油压），胶管是不是有老化的现象。混胶器堵了，清洗混胶器，和里边的混胶棒，另外胶嘴也要清洗。
If your glue gun and mixer are cleaned with kerosene, you need to check whether the glue used now (white glue is OK) is harder than the previous glue. Under the same pressure, the amount of hard glue is smaller than that of thin glue; Whether the pressure of the glue applicator is normal (air supply pressure, oil pressure), and whether the rubber hose is aging. If the glue mixer is blocked, clean the mixer and the glue mixing stick inside. In addition, clean the glue nozzle.
打胶机铝糟探针打胶不准？
Incorrect gluing of aluminum residue probe of gluing machine?
1、放在一个平整干净的平面上，连接电源和气源，两者确认接通之后就开始进行操作。
1. Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected.
2、打胶机中间会有一个混胶过程，在供胶机上面混胶完毕之后，需要在电子显示屏上控制面板上进行选择“行走设置”。打开界面之后按T1键前进行走。在机头停止时，打开机头上面B胶阀门，接着在控制面板上找到Esc键返回主界面，然后F2状态设置，在打开界面后按K3键供胶开始，当胶嘴中完全混合的胶流出按K4键结束供胶。
2. There will be a glue mixing process in the middle of the glue dispenser. After mixing the glue on the glue feeder, you need to select "walking setting" on the control panel on the electronic display screen. Press the T1 key to move forward after opening the interface. When the machine head stops, open the B glue valve on the machine head, then find the ESC key on the control panel to return to the main interface, and then set the F2 status. After opening the interface, press the K3 key to start the glue supply, and when the completely mixed glue in the glue mouth flows out, press the K4 key to end the glue supply.
打胶机故障打第三边时先吸胶再运行？
Glue dispenser failure when the third side is hit, suck the glue first and then run?
打胶机故障，对平方大的玻璃注胶时，打第三边时先吸胶再运行，但是出胶量很少是什么原因？以前是直接四边打完胶再吸胶，现在是打两边后吸胶。出现这个问题原因：一，有异物堵塞出胶管道和出胶口。二，气压或者液压压力减弱。三，胶桶里马上没胶了。检查系统和运行速度。
The glue dispenser fails. When injecting glue into the glass with a large square area, the glue is sucked first and then operated when the third side is applied, but what is the reason for the small glue output? In the past, glue was sprayed directly on four sides and then sucked. Now, glue is sprayed on both sides and then sucked. The reasons for this problem: first, there are foreign objects blocking the glue outlet pipe and the glue outlet. 2、 The air pressure or hydraulic pressure decreases. 3、 There is no glue in the plastic bucket immediately. Check the system and operating speed.
济南双组份打胶机长时间停用时，要拔掉电源，这样不仅可以延长机器的寿命，还可以节省很多传记费。随着日益变化的工业发展，液体控制技术和点火器设备也在不断发展，以超精密控制和多样化及化。
When Jinan two-component gluing machine is out of service for a long time, unplug the power supply, which can not only prolong the service life of the machine, but also save a lot of biographical fees. With the ever-changing industrial development, liquid control technology and igniter equipment are also developing, with ultra precision control and diversification and specialization.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.jntiannuo.com And consult our staff, will serve you wholeheartedly.
上一篇：双组份打胶机的结构原理以及打胶操作
下一篇：环氧树脂灌注胶混胶机相比人工混胶的优势之处
