在使用双组分涂胶机生产的工作中，总结了几个可以避免胶水溢胶、涂覆、灌胶的几个方法和问题的相关处理内容，简单来看看吧。

In the production of two-component glue applicator, this paper summarizes several methods to avoid glue overflow, coating and filling, as well as relevant treatment contents of problems. Let's have a brief look.

双组分涂胶机溢胶时

When the two-component glue applicator overflows

双组分涂胶机在进行连续点胶时，点胶动作在终点前提前关闭。胶水堆积或拉丝现象。

When the two-component glue applicator is continuously dispensing, the dispensing action shall be closed in advance before the end point. Glue accumulation or wiredrawing.

当遇到一些流动性很强的胶水时，双组分涂胶机完成动作后，流道内的胶水会自动流出。这时候只需要在末端位置停留一段时间即可。

When encountering some glue with strong fluidity, the glue in the flow channel will flow out automatically after the two-component glue applicator completes its action. At this time, you only need to stay at the end position for a period of time.

遇到颗粒很小的高粘度胶水时，很容易拉丝，不仅影响产品工艺，还可能影响产品的使用。这时需要在末端位置设置一个回拉动作，可以是向前、向后或向上，视实际生产需要而定，以便将要拉出的那段胶水处理掉。

When encountering high viscosity glue with small particles, it is easy to wire, which will not only affect the product process, but also affect the use of the product. At this time, it is necessary to set a pull back action at the end position, which can be forward, backward or upward, depending on the actual production needs, so as to dispose of the glue to be pulled out.

在点胶过程中，如果想在不浪费太多时间处理胶水的情况下提高产能，可以使用高压吸水阀，可以解决断胶、溢胶、拉丝等问题。

In the dispensing process, if you want to improve the production capacity without wasting too much time dealing with glue, you can use the high-pressure suction valve, which can perfectly solve the problems of glue breaking, glue overflow, wire drawing, etc.

在使用分涂胶机涂覆、灌胶时

When applying and filling glue with a separate glue applicator

双组份打胶机厂家认为需要胶水加工的设备大多采用分涂胶机和灌胶机，在产品表面和内部进行特殊涂胶，达到产品密封、防水、绝缘、防松动、抗老化的目的.在当前的自动化工业生产中，出现了越来越多的涂胶和涂胶要求。以下是涂胶浇注时可能遇到的问题。

The manufacturer of two-component glue applicator thinks that the equipment that needs glue processing mostly adopts separate glue applicator and glue applicator to apply special glue on the surface and inside of the product, so as to achieve the purpose of sealing, waterproof, insulation, anti loosening and anti-aging of the product In the current automatic industrial production, there are more and more gluing and gluing requirements. The following are the problems that may be encountered during gluing and pouring.

胶阀在加工过程中点胶，发生在点胶阀关闭后。主要原因是使用的针直径不匹配。针口直径过小，会限制液体的流动，产生背压，这样点胶阀的残压过大，就会出现滴漏现象。另外，在灌胶过程中，也存在很多气泡问题，也需要灌胶时间。建议是好使用合适的大直径针头。

The dispensing of the dispensing valve occurs after the dispensing valve is closed during the processing. The main reason is that the needle diameters used do not match. If the needle diameter is too small, it will restrict the flow of liquid and generate back pressure. In this way, if the residual pressure of the dispensing valve is too large, there will be dripping and leakage. In addition, there are many bubble problems during the glue filling process, and the glue filling time is also required. It is recommended to use a suitable large diameter needle.

加工过程中出胶量变化很大，胶阀出胶量不同。气压充足，出胶量小，出胶量小，胶阀流速慢，加大流道直径，加大接口接头直径，流道可以被缩短。胶水有气泡，可以用锥形针去除气泡。

The glue output varies greatly during the processing, and the glue output of the glue valve is different. The air pressure is sufficient, the glue output is small, the glue output is small, and the flow rate of the glue valve is slow. By increasing the diameter of the flow passage and the diameter of the interface joint, the flow passage can be shortened. If there are bubbles in the glue, the bubbles can be removed with a conical needle.

双组分涂胶机溢胶、涂覆、灌胶避免方法相关信息已经讲解完毕了，关注我们网站www.jntiannuo.com咨询了解更多事项！

The relevant information about the methods to avoid overflow, coating and filling of two-component glue applicator has been explained. Please pay attention to our website www.jntiannuo Com for more information!