1、 Principle and structure of insulating glass automatic gluing machine

中空玻璃自动打胶机是玻璃深加工设备中产生较晚但用量较大的机械设备之一。，主要作用是将半成品的中空玻璃做好密封，也可以作异形玻璃的密封。正确合理的使用中空玻璃自动打胶机，不仅能保证生产的正常进行，还会起到延长机器寿命的作用。中空玻璃打胶机总共分为三种：立式自动打胶机、卧式半自动打胶机、手动打胶机。

Insulating glass automatic gluing machine is one of the mechanical equipment with late production but large consumption in glass deep processing equipment., The main function is to seal the semi-finished insulating glass, and it can also be used as the sealing of special-shaped glass. The correct and reasonable use of insulating glass automatic gluing machine can not only ensure the normal production, but also prolong the service life of the machine. There are three types of insulating glass glue applicators: vertical automatic glue applicator, horizontal semi-automatic glue applicator and manual glue applicator.

中空玻璃半自动打胶机主要通过打胶机来实现中空玻璃的打胶。客户可以根据自己需要的参数来设置中空玻璃半自动打胶机。

The semi-automatic gluing machine for insulating glass mainly realizes the gluing of insulating glass through the gluing machine. Customers can set the semi-automatic gluing machine for insulating glass according to their own parameters.

卧式中空玻璃半自动打胶机通产是由打胶机、供胶机组成。每个厂家的不尽相同，因为不同的材料和电机会影响机器的精度和使用寿命。通常中空玻璃半自动打胶机的寿命为10—15年。

Horizontal insulating glass semi-automatic gluing machine is composed of gluing machine and glue supply machine. The prices of each manufacturer are different, because different materials and motors will affect the accuracy and service life of the machine. Generally, the service life of insulating glass semi-automatic gluing machine is 10-15 years.

二、怎样调试卧式中空玻璃半自动打胶机

2、 How to debug horizontal insulating glass semi-automatic gluing machine

放在一个平整干净的平面上，连接电源和气源，两者确认接通之后就开始进行操作。打开气泵开关，电源总开关，控制台开关，在控制台按手动按钮，然后在显示屏上找到原点设定，点击辅助原点设定，然后点击头部原点设定，注意原点设定时避免头部和辅助吸盘碰撞。等设定好然后返回找到玻璃厚度设定，先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度，输入完以后，点击设置进入。等命令位置和当前位置数值一致即可，注意设置时传送带上不要有玻璃。然后是混交了，按一桶胶按钮，按工作选择按钮，然后按拍胶启动，在按伐开，此时胶头以出胶，等看不见白胶，以混均匀以后按伐关，在按链接生产线，自动，自动运行，此时可以自动打胶。

Put it on a flat and clean surface, connect the power supply and air source, and start the operation after they are confirmed to be connected. First turn on the air pump switch, the main power switch and the console switch, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid collision between the head and the auxiliary suction cup when setting the origin. After setting, go back to find the glass thickness setting, first the glass thickness, then the aluminum spacer, and then the glass thickness. After entering, click the setting to enter. Wait until the command position is consistent with the current position value. Note that there is no glass on the conveyor belt during setting. Then it is mixed. Press a bucket of glue button, press the work selection button, and then press the glue shooting button to start. When you press cutting on, the glue head will release the glue. When you can't see the white glue, press cutting off after mixing evenly. When you press the link production line, it will run automatically and automatically. At this time, you can apply glue automatically.

调试的注意事项：

Precautions for commissioning:

1、 在当天机器操作完毕后要把胶管内的胶冲出，防止硬化；如果长时间不实用要注意用煤油清洗胶管和胶枪。

1. After the operation of the machine on the same day, the rubber in the rubber hose shall be washed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the hose and gun with kerosene.

2、 双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高，低质量的胶容易堵塞胶管的过滤系统，造成出胶不畅或不均匀。

2. For the silicone glue or polysulfide glue used in the two-component gluing machine, attention shall be paid to that the impurities shall not be too high. The low-quality glue is easy to block the filtering system of the hose, resulting in poor or uneven glue delivery.

3、 在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净，行清洗，因为不同品种甚的胶容易反应堵塞机器。

3. When changing the type of glue, pay special attention to flush the residual glue in the two-component gluing machine and clean it first, because different types and even brands of glue are easy to react and block the machine.

液压站系统的压力，不能调的太高，要根据室内环境温度等实际情况，调满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪，否则B组份管路压力将升得很高，造成事故。

The pressure of the hydraulic station system cannot be adjusted too high. According to the actual situation such as indoor ambient temperature, adjust it to meet the normal glue output of the glue nozzle and apply glue evenly. When opening the hydraulic station, be sure to open the glue gun, otherwise the pressure of component B pipeline will rise very high, resulting in accidents.

本文由双组份打胶机为您提供，我们的网站是：http://www.jntiannuo.com我们将以全心全意的热情为您提供服务，欢迎您的访问！

This article is provided by the two-component glue applicator. Our website is: http://www.jntiannuo.com We will serve you with wholehearted enthusiasm. Welcome to visit!