点胶机常见故障及处理方法

点胶机主要分为半自动点胶机、自动点胶机和全自动点胶机这几种类型。无论是哪种点胶机，在使用过程中都不可避免的会为遇到一些小问题。如果客户能够分析这些问题的原因并找到解决办法，他们就可以更顺利地使用使用点胶设备，大大的减少客户找人员解决问题的时间。下面，将为大家介绍一些压盘泵点胶机使用过程中常见的故障原因分析及解决方法。
Dispensing machine is mainly divided into semi-automatic dispensing machine, automatic dispensing machine and automatic dispensing machine. No matter what kind of dispenser, in the use of the process will inevitably encounter some small problems. If customers can analyze the causes of these problems and find solutions, they can use dispensing equipment more smoothly, greatly reducing the time for customers to find professionals to solve problems. Next, we will introduce some common fault cause analysis and solutions in the use of dispensing machine.
一、点胶机流体内有气泡的原因及解决办法
1、 Causes and solutions of bubble in dispensing machine fluid
原因：
reason:
点胶机由于过大的流体压力和加上过短的开阀时间，会有可能将空气渗入液体内，造成气泡的产生。
Due to excessive fluid pressure and short valve opening time, air may seep into the liquid and cause bubbles.
解决方法：
resolvent:
降低流体压力并使用锥形斜式针头。
Reduce fluid pressure and use a tapered, oblique needle.
二、点胶机出胶大小不一致
2、 Dispensing machine glue size is not consistent
原因：
reason:
点胶机储存流体的压力筒或空气压力不稳定，导致出胶不均匀，大小不一致。
The pressure cylinder or air pressure of the dispenser storing fluid is unstable, resulting in uneven glue output and inconsistent size.
解决方法：
resolvent:
应避免使用压力介于压力表之中低压力部分。胶阀控制压力应少60psi以上以确保出胶稳定。 后应检查出胶时间，若小于15/1000秒会造成出胶不稳定，出胶时间越长出胶越稳定。
The low pressure part of the pressure gauge should be avoided. The control pressure of the rubber valve should be at least 60 psi to ensure stable glue delivery. After that, the glue out time should be checked. If it is less than 15 / 1000 seconds, it will lead to the instability of the glue. The longer the glue time is, the more stable the glue will be.
三、点胶无法停胶
3、 Unable to stop dispensing
原因：
reason:
1.点胶阀中转杆或密封装置磨损
1. The transfer rod or sealing device of dispensing valve is worn
2.点胶阀的气压是否断开。
2. Whether the air pressure of dispensing valve is disconnected.
解决办法：定期检查设备，更换磨损设备。
Solution: check the equipment regularly and replace the worn equipment.
在使用点胶机时，如果客户遇到上述故障，建议根据上述分析检查故障原因，进行处理。如果遇到同样的情况，可以根据有关方法进行求解，应能大大节省了时间。
When using the dispenser, if the customer encounters the above failure, it is recommended to check the cause of the failure according to the above analysis and deal with it. If the same situation is encountered, it can be solved according to the relevant methods, which should save a lot of time.

上一篇：影响自动点胶机胶体粘度的原因
下一篇：压盘泵打胶机如何控制胶量？