Hollow glass glue machine is very simple in function. Focus on the insulating glass gluing, but the insulating glass gluing machine may encounter the problem of incomplete gluing in the gluing process. Today, we specially introduce the insufficient glue of the insulating glass glue machine.

　　事实上，我们出现这个问题主要是由以下三个条件造成的!

　　In fact, we have this problem mainly caused by the following three conditions!

　　，上胶速度太快

　　First, the speed of glue application is too fast

　　一些客户为了加快自己的生产节奏生产计划后,调整密封剂认为速度太快,导致胶体仍没有完全达到合格标准的头已经到下一个位置胶操作,如果我们需要加速调整胶胶机运动参数,所以我们也要有相应的相应设置胶供应系统,如这一次我们需要增加供应压力,增加上胶速度，使上胶机随物体移动速度增加。如果我们只增加胶水机的速度，而不调整压力，很可能是胶水不够。

　　In order to speed up the production schedule, some customers adjust the sealant to think that the speed is too fast, so that the head of the sealant which still does not meet the qualified standard has been moved to the next position for glue operation. If we need to speed up the adjustment of the movement parameters of the glue machine, we also need to set the corresponding glue supply system, such as this time we need to increase the supply pressure, increase the glue speed Degree, so that the glue machine with the object moving speed increases. If we only increase the speed of the glue machine without adjusting the pressure, it is likely that the glue is not enough.

　　2. 供胶压力不足

　　2. Insufficient glue supply pressure

　　事实上，这种情况在前一种情况中已经描述过了，即使不调整胶水机的速度也会出现打胶不满的情况，那么有可能供应的胶水压力太小。此时我们只需要调整上胶压力就可以解决这个问题。

　　In fact, this situation has been described in the previous situation. Even if the speed of the glue machine is not adjusted, there will be insufficient glue application. Then it is possible that the glue pressure supplied is too small. At this time, we just need to adjust the glue pressure to solve this problem perfectly.

　　3.鼻子损坏传感器

　　3. Nose damage sensor

　　这种情况非常罕见，但不能排除。在我们的中空玻璃上胶机的头部，有一个传感器可以检测铝带的深度。如果铝带过深或过浅，会自动调节移动速度和上胶压力(自动调节范围小)。这可能会发生，如果我们的铝带本身是不同的色调，加上损坏我们的传感器!

　　This is very rare, but it cannot be ruled out. At the head of our insulating glass gluer, there is a sensor that can detect the depth of the aluminum strip. If the aluminum strip is too deep or too shallow, it will automatically adjust the movement speed and glue pressure (the automatic adjustment range is small). This can happen if our ribbon itself is of different hues, plus damage to our sensors!

　　希望通过小编的表达可以在你的设备中找到这种问题的时候可以有效的解决问题，不用担心这个问题。如果您对中空玻璃上胶机有任何问题，请随时与我们联系。

　　I hope that this kind of problem can be found in your device through the expression of Xiaobian, which can effectively solve the problem without worrying about it. If you have any questions about the insulating glass gluing machine, please feel free to contact us.