There are different types of glue machines often use glue, it can be said that more than similar products, each model has different performance, glue commonly used in glue coatings, channel end glue machine can be used, can only comment on some of the more common glue, to meet some basic paint industry, the use of pressure barrels.

　　一、常用胶水种类

　　Types of common glue

　　胶机常用的涂层胶分别用银胶、红胶、热熔胶、硅胶、AB胶、快干胶、焊锡膏、环氧天然橡胶、填充底部的橡胶、乙烯基、厌氧胶、耐高温胶、白胶等等,这些都是常用的涂层胶,胶与通道胶机可以使用,但需要更换一些配件,可以满足生产的需要,上胶阀对上胶有几种要求较高，类似于硅酮、热熔胶、红胶、厌氧胶等需要特殊的上胶阀设备才能达到真正上胶的末端要求。

　　The commonly used coating adhesives for rubber machines are silver glue, red glue, hot melt glue, silica gel, AB glue, quick-drying glue, solder paste, epoxy natural rubber, rubber filled with the bottom, vinyl, anaerobic glue, high temperature resistant glue, white glue, etc. These are commonly used coating adhesives. The glue and channel glue machine can be used, but some accessories need to be replaced. To meet the needs of production, there are several kinds of higher requirements for gluing valves. Similar to silicone, hot melt glue, red glue, anaerobic glue, special gluing valve equipment is needed to achieve the end requirements of real gluing.

　　其次，使用压力桶要注意问题

　　Secondly, attention should be paid to the use of pressure barrels.

　　是否需要这些类型的胶水来填充压力桶?对特定的需求,自动化生产是不需要通过更换可能每次胶,使用气动式压力桶来满足通道胶机连续胶的要求,只有压力桶必须注意使用方法,或特别容易出现胶水供应不足,导致没有胶水,胶水使用胶水每个日出生产是非常大的。

　　Do you need these types of glue to fill pressure barrels? For specific requirements, automatic production does not need to replace each possible glue, using pneumatic pressure barrel to meet the requirements of continuous glue channel glue machine, only the pressure barrel must pay attention to the use of methods, or especially prone to glue shortage, resulting in no glue, glue to make. It is very big to produce glue every day.

　　三、浇注塑料桶的应用方法

　　3. Application Method of Casting Plastic Barrel

　　如何使用沟道浇注机的气动压力桶?相对短暂,要了解胶水的性质,然后观察浓度条件下,特别容易冷凝式连续混合,避免冷凝,更高水平的胶是一样的,有一个低降水的胶水,胶水浓度还需要添加混合,然后加入胶桶式气压,气压管、压力释放阀、防爆阀、等,密封,以避免泄漏,然后接软管胶机、这样的基本是有联系的。先在压力桶内满压后，再用槽口浇注机抽胶，以免导致胶水断续。

　　How to use the pneumatic pressure barrel of the channel pouring machine? It is relatively short. First, we need to understand the nature of glue. Then, we should observe the concentration conditions, especially easy to condense continuous mixing, avoid condensation. Higher level glue is the same. There is a low-precipitation glue, the glue concentration also needs to be mixed, and then add the barrel pressure, barometric pipe, etc. Pressure release valves, explosion-proof valves, etc., are sealed to avoid leakage, and then hose glue machine, which is basically related. After full pressure in the pressure barrel, the glue is drawn by the groove pouring machine to avoid intermittent glue.