How to replace another glue after the glue filling machine is finished?

　　不少客户在运用灌胶机打商品时，因为技术纷歧样，也许在打此外某类商品时需替换胶水，纷歧样品种的胶水夹杂在一起，会起化学反映，会引起胶水中毒，致使灌出的商品达不到质量需求。所以在替换胶水时必然要做好洁净工作，下面由灌胶机厂家信华为我们作一下介绍：灌胶机清洗事项

　　Many customers use glue machine to make goods, because the technology is different, maybe they need to replace glue when they make some other goods. The glue mixed with different samples will cause chemical reaction, which will lead to glue poisoning, so that the products can not meet the quality requirements. So when replacing glue, we must do a good job of cleaning. Below, Xinhua, the glue machine manufacturer, will introduce the cleaning of glue machine.

　　1. 请与胶水供应商承认胶水洁净剂。

　　1. Please acknowledge the glue cleaner with the glue supplier.

　　2. 封锁AB料桶底部阀门。

　　2. Block the bottom valve of AB barrel.

　　3. 操作设备出胶，将残留在胶阀，高压铁氟龙管，AB泵内部的胶水打出，可查询拜访胶阀出胶口胶量改变，判断内部胶水已排空。

　　3. Operating equipment gum out, the glue remaining in the rubber valve, high-pressure ferrofluorine hose, AB pump out, you can inquire about the change of gum volume at the rubber valve outlet, judge that the internal glue has been emptied.

　　4. 封锁设备总电源。

　　4. Blocking the general power supply of the equipment.

　　5. 拆开料桶底部胶管，翻开阀门，将料桶残剩胶水排出。

　　5. Remove the rubber hose at the bottom of the barrel, open the valve and discharge the residual glue from the barrel.

　　6. 封锁料桶底部阀门，将适量洁净剂倒入料桶，将桶壁与桶底残剩的胶水洁净干净。

　　6. Block the bottom valve of the barrel, pour a proper amount of cleaner into the barrel, and clean the remaining glue on the barrel wall and bottom.

　　7. 翻开料桶底部阀门，将污水排出，料桶不行有残渣。

　　7. Open the bottom valve of the barrel and discharge the sewage. There is no residue in the barrel.

　　8. 拆下AB泵，将泵内部胶水整理干净(需受过拆装泵操练人员操作此项)。

　　8. Remove the AB pump and clean up the glue inside the pump (it needs to be operated by the operator who has disassembled and assembled the pump).

　　9. 将干净AB泵装回原位，与料桶胶管从头接上。

　　9. Install the clean AB pump back to its original position and connect it with the barrel hose from scratch.

　　10. 灌胶机替换高压铁氟龙管。

　　10. Replace high-pressure ferrofluorine hose with glue filler.

　　11. 倒入新胶水。

　　11. Pour in new glue.

　　12. 敞开设备，点动出胶3~5分钟，承认胶水出胶正常。

　　12. Open the equipment and point out the glue for 3-5 minutes. Admit that the glue is normal.

　　13. 从头分配AB胶水比例。

　　13. Distribution of AB glue ratio from scratch.

　　依照上面过程，将全部灌胶机洁净干净，再换胶水去灌胶凡是是不会呈现质量疑问的。

　　According to the above process, all the glue-filling machines will be clean and clean, and then change the glue to glue-filling will not always present quality doubts.